|
Tractor Talk Discussion Board |
Re: O/T Electric wireing
[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]
Posted by John T on March 29, 2006 at 14:26:04 from (66.244.90.98):
In Reply to: O/T Electric wireing posted by VADAVE on March 29, 2006 at 11:30:17:
Dave, that wiring method is as old as my mother in law and hasnt been NEC code legal for yearsssssssssssss. The proper NEC and state of the art and trade name/reference for modern house wiring is 120/240 Volt, Single Phase, 3 wire. It is an earth grounded system NOT a floating service. At the service transformer the Neutral is earth grounded (also grounded on high voltage primary side if a Y service) then again at the service entrance. ONLY at the main service entrance are the Neutral and Ground Busses bonded together (NOT at sub panels) and the Neutral is bonded to a grounding electrode which leads to the earth ground reference like a made ground such as a driven ground rod. Nowwwww 3 phase can be either Wye (which is usually earth grounded) or Delta (which is usually floated although I have corner grounded them). A 3 Phase 4 Wire Wye circuit carries 3 hots, a Neutral, and an equipment ground. At the service entrance the Neutral and Ground busses are bonded, same as in the 1 Phase 3 Wire home system. Typical of voltages are 208 Y 120 or 480 Y 277. A 3 Phase 3 Wire floating Delta circuit carries 3 hots and an equipment ground (has no Neutral). Typical of voltages are 240 or 480. There can also be a hot or high leg 120/240 volt 3 phase 4 wire Delta configuration in which one transformer has a center Neutral which is earth grounded and off that transformer one gets 120 volt single phase (2 legs) or 240 volt single phase. Hope this helps yall John T (retired electrical engineer who designed secondary power distribution systems)
Replies:
Home
| Forums
| Order Support
Today's Featured Article -
Hydraulics - Cylinder Anatomy - by Curtis von Fange. Let�s make one more addition to our series on hydraulics. I�ve noticed a few questions in the comment section that could pertain to hydraulic cylinders so I thought we could take a short look at this real workhorse of the circuit. Cylinders are the reason for the hydraulic circuit. They take the fluid power delivered from the pump and magically change it into mechanical power. There are many types of cylinders that one might run across on a farm scenario. Each one could take a chapter in
... [Read Article]
Latest Ad:
1958 FORD RARE 4x4 801 TRACTOR, ELENCO/FRONT DRIVE, FRONTLOADER AND WEIGHTED REAR WHEELS, FIVE SPEED, LIVE PTO, GAS ENGINE, NEW REAR WHEELS AND TIRES, ENGINE RUNS.
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|