|
Tractor Talk Discussion Board |
Re: disconnecting bush hog from tractor
[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]
Posted by Billy NY on January 04, 2006 at 15:20:57 from (64.12.117.7):
In Reply to: disconnecting bush hog from tractor posted by john wilson on January 04, 2006 at 12:54:38:
I had this happen on our challenger tractor this summer, saw one of our guys hooking up the post hole digger, I knew it had not been in service for awhile and it actually was froze into the ground inside the one barn that takes on water every year, I saw the yoke was rusted, and I asked him, "did you clean out and lube the splines 1st ? The lying p.o.s said "yes", when I went to unhook the P.T.O. shaft, it would not budge, was 95 deg F out and humid, after working at it with a 6'-0" bar for over an hoour,after I did find a way to get a bite on the edge of it without wrecking anything, it slowly was persuaded to slide off, was still rusted, and no lube on it. I really hate a liar, so now, no one is allowed use of our equipment, can't trust them to grease and take care of things properly, just have to do it by hand, or wait for me. I can't ever recall having this kind of a problem, with any P.T.O. driven implement since I started as a kid. I cleaned the splines carefully with a wire brush and applied my favorite grease, so much easier, slides nice now, rusty splines and the fact that he jammed it on the P.T.O. shaft sure bonded the 2 togehter tightly. Everyone has their snake oil, I like Kroil by Kano Labs and Free All, by Federal Process, for tough jobs, PB, WD, Liquid Wrench have always done fine, but for the tough jobs these have proven themselves too, Free All is kind of expensive per can, but you don't use much, a can will last will last quite some time on average, has that heavy industrial aroma to it, must have some volatile organic compounds in it, something about the hideous smell of some of these, makes you think it's strong at least.
Replies:
Home
| Forums
| Order Support
Today's Featured Article -
The Engine Rebuild Kit - by Curtis Von Fange. I always liked engine rebuild kits. They have all the replacement parts for overhauling an engine without going to the store to get gaskets, special measuring tools, or miscellaneous parts. They come neatly packaged, clean and tidy. But it's important not to let that packaging lull you into a false sense of security. The appearance of matching sleeves, pistons, rings, and bearings can cause frustration and agony if not properly measured and installed in a workshop environment. Following c
... [Read Article]
Latest Ad:
one 8n and one 9n tractor. totaly restored,pretty much everything is new. one 6ft blade good shape.
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|