Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: Putting Rear Tube Tire on Rim?


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by Hoosier JD on December 02, 2005 at 14:02:21 from (64.12.117.7):

In Reply to: Re: Putting Rear Tube Tire on Rim? posted by Buster on December 02, 2005 at 12:50:07:

It has been a lot of years, but I put myself through college working in a tire store. First, we were told to never put any kind of oil on tires to mount them, especially car on truck tires, the tire might slip on the rim and lose the seal between bead and the rim, soapy water is fine...even recommended. Next, tire "spoons" are a great help, these are the specialized bars to pry the tire off or on. "Duck-billed" tire hammers are good for hammering the bead on, you can also use the hammer to break the bead loose from the rim, that's how I do all of mine here at home. As far as the tire-tube, make sure the rim is clean and rust free, pry or hammer on the first or back bead of the tire, insert the tube, put some air in the tube...just enough to take the slack out of the rubber with the valve fastened in the valve hole. Then carefully pry the front bead on. When airing the tire up, watch the beads and make sure they are seating against the rim correctly...if not, let it part way back down and try again. After the tire is fully inflated and seated, we were told to let the tire completely deflate to lessen the chance of the tube being wrinkled and pinching itself. Tire and wheel mounting is a very dangerous operation, if you can afford it, take it to the experts. I could tell hundreds of stories about guys getting injured working on wheels and tires. This not a complete or exact step by step explanation, and I get concerned when I hear of guys, no matter how mechanical or adept at doing things by and for themselves, tackle tire changing. Good luck. Mike


Replies:




Add a Reply

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - History of the Nuffield Tractor - by Anthony West. The Nuffield tractor story started in early 1945. The British government still reeling from the effects of the war on the economy, approached the Nuffield organization to see if they would design and build an "ALL NEW" British built wheeled tractor, suitable for both British and world farming. ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy