Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: shotgun chokes, which to use


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by R. John Johnson on November 26, 2005 at 06:13:49 from (205.200.43.138):

In Reply to: shotgun chokes, which to use posted by Rich Iowa on November 26, 2005 at 04:09:02:

Rich

Some of this depends on how you are hunting. If it is over a pointing dog they will be close shots and an Improved Cylinder choke would be my choice, since the birds would be close. If you are hunting over flushing dogs or without a dog and people driving the birds to flush them, they will be getting up further away. This calls for a modified chioke. Since you said you would not be taking shots over 40 yards, leave the full choke at home. When I lived in South Dakota and hunted Pheasants, I used Federal 2 3/4 Dram (1330 FPS) 1 1/4 #5's. Less pellets than the #6, but more retained energy to penetrate the vitals.

One last thing. Don't assume that since the choke tube says Modified that it is Modified. Get a big sheet of paper or cardboard, large enough to draw a 30" circle. Set it up at the range you will be shotting and fire one shot into it. If you want to get persnicity, you can cound pellet holes and figure your pattern percentage, but mainly I would be sure there were no giant gaps in the pattern and that it covered the 30" circle. I have a Rem IC choke that will pattern full choke percentages with a specific target load.

Good luck!

John


Follow Ups:




Post a Followup

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - The Tractor Parade: Story of a Case SC - by Bernie DeLon. On a early fall morning back in 1994, I opened the newspaper and happened to spy an article about a local antique tractor club having their annual show that weekend. ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy