|
Tractor Talk Discussion Board |
Re: Rear mounted snow blower on a john deere
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by pete-mi on October 09, 2005 at 21:13:54 from (199.176.224.205):
In Reply to: Rear mounted snow blower on a john deere posted by wayneaviator on October 04, 2005 at 18:47:11:
I have a 84 inch 3pt rear pull blower on JD 4020 and it works great. I have used the rear pull type for over 15 years. As long as the tractor can drive through the snow you can blow it. I have blown snow deep enough with snow going over the front axle. On a very rare ocasions I have had to back into a drift but it averages only one or two times a season. So it averages to less than 10 min per season. I only own 2wd tractors and the tires are not loaded. The only thing posibly better than the rear pull is a front mount but I would prefer to have it on a 4wd as the blower weight is out front. They also cost a fair bit more $$. I have used the backup type before and hope never to have to again. Twisting around all the time to see where you need to blow is no fun !!! About the main thing these are good for is moving snowbanks or real small straight drives. Using a snowblower to start with eliminates 99% of the snowbank problems. The rear mount blowers cost the least but are harder on the operator to use. I paid a little extra and got the rear pull and am glad I did. My back and neck feel a lot better after spending 2 hours blowing snow. I do my own place and a couple neighbors. One other item that is very nice to have is a cab or at least a heat houser.The 2 stage type blowers are the best for wet heavy snow as the auger feeds it into the blower fan. I would look into geting a rear pull or a front mount blower.
Follow Ups:
Home
| Forums
| Order Support
Today's Featured Article -
12-Volt Conversions for 4-Cylinder Ford 2000 & 4000 Tractors - by Tommy Duvall. After two summers of having to park my old 1964 model 4000 gas 4 cyl. on a hill just in case the 6 volt system, for whatever reason, would not crank her, I decided to try the 12 volt conversion. After some research of convert or not, I decided to go ahead, the main reason being that this tractor was a working tractor, not a show tractor (yet). I did keep everything I replaced for the day I do want to restore her to showroom condition.
... [Read Article]
Latest Ad:
1958 FORD RARE 4x4 801 TRACTOR, ELENCO/FRONT DRIVE, FRONTLOADER AND WEIGHTED REAR WHEELS, FIVE SPEED, LIVE PTO, GAS ENGINE, NEW REAR WHEELS AND TIRES, ENGINE RUNS.
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|