|
Tractor Talk Discussion Board |
Re: White Mighty Hoe
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by astaylor on August 09, 2005 at 17:43:34 from (71.1.13.35):
In Reply to: White Mighty Hoe posted by BrandonBaxter on August 09, 2005 at 16:45:17:
Sir, I too am the proud owner of a 2 63 15 MH with the 6, a Reverse-o-torque trans etc... These are wet sleeved motors, they are real solid and all but through the years parts will begin to fail. There are three areas to address when you find coolant in your oil, the head gaskets, the cylinders / seals or the block are the points of failure. I have just run through mine for the same reason and found the seal on the bottom of #3 went out. It is most likely a strait forward fix which is the good news, the bad news is that it will require a teardown. Start with a compression check, fairly easy due to fact that the head has plug holes, if you find a cylinder that is off by say 20% or more then you have your problem located, only question is weather it is the head, gasket or cylinder parts. If all cylinders are equal or close then look at a rebuild kit, you are going to be inside and might as well freshen up the unit while you are there. A few questions, what are the hours on the motor, where are you located in the states and how much do you use the rig? These are real popular motors due to their being used on Oliver�s from the 1650 up to the 1800 or so, and parts are out there. I have a list of dealers with some parts but I am in Florida, you can also contact Agco, they are the new owners of White, Oliver, MM and MF, they have a list of dealers in your area and are on the www. Also this forum is real good for the transfer of knowledge and parts, find the problem and repost for parts. I also have the parts, service and operators manual if you need them for the price of coping them and S&H, just let me know. AT
Follow Ups:
Home
| Forums
| Order Support
Today's Featured Article -
A Tractor's Point of View - by John Manley. I began my life on August 3,1941. I was actually built at different times and days but I was officially an M Farmall on August 3.I was real nice and shiny. That�s me, in the old picture, third from the left. I was loaded on that train and sent to a little town in South Carolina. I didn�t get to see much of that town. I was moved off the train fast and on to the dealer�s
... [Read Article]
Latest Ad:
1958 FORD RARE 4x4 801 TRACTOR, ELENCO/FRONT DRIVE, FRONTLOADER AND WEIGHTED REAR WHEELS, FIVE SPEED, LIVE PTO, GAS ENGINE, NEW REAR WHEELS AND TIRES, ENGINE RUNS.
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|