|
Tractor Talk Discussion Board |
Re: Cub with belly mower - any good?
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Buzzman72 on July 11, 2005 at 07:46:27 from (63.189.209.6):
In Reply to: Cub with belly mower - any good? posted by ags1 on July 11, 2005 at 06:29:53:
A lot of the answer to your question is, "it depends..." As in, it depends on the condition of the Cub (assuming you ARE talking about a regular Cub and not a Cadet), it depends on the mower, and it depends on what you're cutting. When I was a teenager, Dad had a Cub that he did custom mowing with. With a Woods 42C belly mower, that Cub would cut just about anything you could get under it...of course, the 2450 rpm governor off a power unit was a big help, as was the drilled-out carb jet. We also used a Mott Hammerknife belly mower for a time, and it was great on straight lawns...as was the Woods 59. And the Cub-22 sickle mower managed to do a wonderful job on the stuff where it was needed, especially when Dad had a contract with the town mowing street and alley rights-of-ways. But if you expect the Woods 59 (or the IH 5-foot belly mower) to do a bush-hog type of job, you'll be disappointed because the mower simply pulls too hard to effectively cut the heavy stuff (and it uses "lawn-mower" blades, instead of the heavy swinging-type blades that the Woods 42C has). But conversely, with the Woods 42C, as long as you keep the blades fairly sharp and don't mow any stumps or rockpiles, you can still get a lawn-quality job from it as well. I spent a lot of hours of seat time on that Cub, sometimes six days a week when the weather allowed, so if the Cub is in good mechanical shape and you have the right belly mower for the type of mowing you intend to do, I think you'll be quite pleased with its performance.
Follow Ups:
Home
| Forums
| Order Support
Today's Featured Article -
Fasteners: The Nuts and Bolts of Nuts and Bolts - by Curtis Von Fange. The nuts and bolts of nuts and bolts is an interesting and essential piece of knowledge that applies to our older tractors. An improperly torqued capscrew on an engine head or a shear bolt that is too hard on the driving shaft of a bushog can create havoc and make an expensive and uncalled for repair. Let�s examine the purpose and design of these fasteners in order to ensure their proper use. Fasteners are probably one of the aspects of mechanics that is given the least amount of thought.
... [Read Article]
Latest Ad:
one 8n and one 9n tractor. totaly restored,pretty much everything is new. one 6ft blade good shape.
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|