|
Tractor Talk Discussion Board |
Re: OT/ 97 chevy trans??????????
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by txgrn on June 30, 2005 at 04:26:39 from (209.151.118.189):
In Reply to: OT/ 97 chevy trans?????????? posted by vabill on June 30, 2005 at 03:59:30:
You have a bunch of fluid in the system; don't remember the exact value. The sump holds 4 to 5 qts and the torque converter a lot more. Used to be you could drain the torque converter as it had a drain plug, but Detroit decided that the process unecessary; just periodic changing of the fluid and filter in the sump (on some vehicles) was adequate to keep the fluid fresh. I think fluids are better now. So when you say you used the wrong fluid what did you use? Ford Type F? Regardless, 1 qt in that system is like 5% and I wouldn't personally go into hysterics over it. If you put fluid it in it is in the same family (refining of fossel fuels); just different cooking and different additives. But if you do want to drain it all, without having to remove the transmission to get the torque converter off to pour the fluid out (big job) I have done the following: Get a case of tranny fluid. Drop the pan and drain off what's there. Replace the pan (temporarily; use the existing gasket and just a few screws, and fill with a normal fill of fluid. Run the engine for 5 minutes running thru the gears. Shut her off and drain. I think you can do that twice more and have one filling left in the case of fluid you bought. Then put in a new filter, gasket, close her up and fill with the normal fill of desired fluid. You're good to go. I have done this on older cars that I have bought which had the fluid burnt and I wanted fresh. Worked great but was a mess; but was worth it....didn't have any tranny problems on the old geese (did it to more than one). My 2c Mark
Follow Ups:
Home
| Forums
| Order Support
Today's Featured Article -
Fabricating Sidesheets - by Chris Pratt. The easiest and best first-time project for wanna-be sheet-metal workers like myself is flat or nearly flat metal cut and drilled to be a tractor's sidesheet. A sidesheet is sheetmetal to cover either the engine as in the case of early Oliver's, Massey-Harris' and many crawlers or the wiring and electrical components as in the case of the Massey-Harris Pony, Allis Chalmers' D Series (D-14, D-15, D-12, D-10, D-17, and D-19). The need for fabricating becomes obvious when you go to buy any of these
... [Read Article]
Latest Ad:
For sale Farmall super A tractor is complete and has just been setting for awhile,it was running when pulled out of the barn,shouldn’t take to much to get it going asking 1100.00
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|