|
Tractor Talk Discussion Board |
Re: Chrome Stack
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by txgrn on June 05, 2005 at 05:41:58 from (209.151.114.125):
In Reply to: Chrome Stack posted by Brian J on June 04, 2005 at 20:49:39:
Funny you mentioned that. I recently bought a 4230 with a 404 cu in engine. It had a 1 7/8 ID outlet on the muffler along with a 31" pipe. Thought it was restrictive as you could put your hand in the exhaust outlet at pto rpms and it was a solid stream of gas. Took the muffler off and the inlet was over 3" and I thought......who's foolin whom. The manufacturer of the engine (one Deere engineer) decides that proper breathing for the engine is 3+ inch exhaust, and another Deere engineer decides that he is going to make the tractor quiet so he strangles the engine to quieten it down.....but it didn't do much good; still was loud. Since the engine is running hotter than I want it to, under pretty good load with the A/C on, and all the other things have been tended to, the only thing left was restrictive exhaust to contribute to engine heat. Tried to get a muffler for a 4240 as it had a larger outlet but the muffler mfgr suggested a straight pipe instead. So yesterday UPS stops by and drops off a beautiful straight chrome stack that is the same diameter all the way as the hole in the exhaust manifold (over 3") and 50 something inches long with a flange on the engine end. Put it on and it looks great sitting in front of the cab. Cranked her up and it was loud, but not that loud and the soundguard cab blocks a lot of it, plus I wear ear plugs anyway. The engine it'self makes as much noise as the exhaust; especially the fan. The sound is good and solid and the pipe is less vision restrictive than the muffler. So now at PTO rpm's I put my hand in the exhaust and I feel pulses......YEAH! We're breathing now. Can't wait till I can get a load on her and see if it does the job. I'm saving the old stuff in case I have to go back for some reason. My 2c Mark
Follow Ups:
Home
| Forums
| Order Support
Today's Featured Article -
Show Coverage: The Old Gold National Antique Tractor Show - by Cindy Ladage. Over the fourth of July weekend, the Illinois State Fairgrounds in Springfield, Illinois, was the site of the Old Gold National Antique Tractor Show. Tractors of all makes and models were displayed and separted into categories by their age. Deere, Oliver and even a Wards and Keck Gonerman were part of the crowd. A sea of red International Harvester's seemed to be the the model with the biggest showing. The crowd was decent for the scorching July heat. The opening day started o
... [Read Article]
Latest Ad:
1958 FORD RARE 4x4 801 TRACTOR, ELENCO/FRONT DRIVE, FRONTLOADER AND WEIGHTED REAR WHEELS, FIVE SPEED, LIVE PTO, GAS ENGINE, NEW REAR WHEELS AND TIRES, ENGINE RUNS.
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|