|
Tractor Talk Discussion Board |
Re: Gas John Deere 4020 Spark Plug Fowling
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Gerald J. on April 19, 2005 at 07:45:22 from (67.0.109.70):
In Reply to: Gas John Deere 4020 Spark Plug Fowling posted by Jerry Young on April 19, 2005 at 06:09:56:
My 4020 gas smoked like an IH diesel when I first got it a few years ago. I believe the long intake manifold makes it hard to get a decent mixture to the end cylinders (lots of condensation until the manifold heats and JD does call for manifold heat up to 90 when not loaded hard) and to the center two cylinders at the same time. However, I found a few things to make it burn a leaner mixture and never touched the carburetor settings. 1. I made sure the choke opened all the way. The choke cable sheath wasn't anchored near the carburetor and would open only half way. 2. I cleaned junk out of the intake. 3. I cleaned the air cleaner (dry). 4. I pushed the dome of the Donaldson precleaner up instead of down where it had been pulled from over tightening over the decades. 5. I replaced the float needle and seat. 6. I went to a higher heat range AC plug, No Champion plugs. 7. I put in copper wires. 8. I timed it to 20 degrees before top dead center with .020 point gap while at 2000 rpm per the owner's manual. The first year I burned 400 gallons, the next year doing the same work, I burned 250 gallons. I've not changed the plugs in at least 150 hours. I have to use the choke when starting, often even when its warm. I don't have manifold heat on because some unkind soul cranked in a pipe plug into the heat shrowd of the intake manifold and split it. It doesn't like 10% ethanol, probably because of the cold manifold that I ought to fix some of these years. You could try to reduce the output of the accelerator pump in the carburetor. You could increase the distance between the float and the flange to lower the fuel level and so lean the mixture over the entire running range of the carburetor. Gerald J.
Follow Ups:
Home
| Forums
| Order Support
Today's Featured Article -
Identifying Your Tractor - by Staff. Maybe you bought it from a friend who didn't know what kind of tractor it was, or perhaps (and this is every tractor fanatics dream) you stumbled across it in an abandoned field covered with weeds but intact. In any case, you have no idea what the make and/or model is. For awhile perhaps it doesn't really matter. Especially if it runs! But pretty soon you'll probably need to tinker with it a bit and maybe buy a part or too. Having a manual is nice. But how does one go about dete
... [Read Article]
Latest Ad:
For sale Farmall super A tractor is complete and has just been setting for awhile,it was running when pulled out of the barn,shouldn’t take to much to get it going asking 1100.00
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|