|
Tractor Talk Discussion Board |
Re: Want to build a polebarn, where to start?
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Mark - IN. on March 20, 2005 at 05:40:50 from (205.188.117.66):
In Reply to: Want to build a polebarn, where to start? posted by Mike from cny on March 19, 2005 at 17:23:00:
There are several good kits out there, and most run comparable on prices, and the labor to put it up is about as much as the price itself, if you pay to have it put up. It cost me $65 an hour to have a guy bring out is Case 450 and level it for a few hours. That was cheap, considering that I tried it with a backblade first and...well, I'm not good at that. Then $12.5K for the materials on a 40x60, and another $12.5K to put it up. Concrete is included. Thing is, I'm in another state working all week, and needed to get it up. Make sure your doors are big enough. I went with 12' wide doors, now I'm headin out after this to auger down and drop two more posts before they bring the concrete so have 14' wide doors. Now gotta take some metal down, fasten the cross-2x4's into the new posts, pull the old ones out, trim those cross-2x4's off, take all of the metal off of the doors, remake the door frames, and put all the metal and some new back on the doors. It's do-able, just could've been avoided with a little more thought on my part first. Good thing the concrete aint coming for a couple of weeks. When you think you know how big your doors gotta be, add at least a couple of feet. My doors are opposite of each other at both ends of the building, clear to one side so I can pass through the building without having to move stuff. Some guys center their doors for combines and stuff that can't make tight turns. Be careful where you position your doors too - it make a difference. Mark
Follow Ups:
Home
| Forums
| Order Support
Today's Featured Article -
12-Volt Conversions for 4-Cylinder Ford 2000 & 4000 Tractors - by Tommy Duvall. After two summers of having to park my old 1964 model 4000 gas 4 cyl. on a hill just in case the 6 volt system, for whatever reason, would not crank her, I decided to try the 12 volt conversion. After some research of convert or not, I decided to go ahead, the main reason being that this tractor was a working tractor, not a show tractor (yet). I did keep everything I replaced for the day I do want to restore her to showroom condition.
... [Read Article]
Latest Ad:
1958 FORD RARE 4x4 801 TRACTOR, ELENCO/FRONT DRIVE, FRONTLOADER AND WEIGHTED REAR WHEELS, FIVE SPEED, LIVE PTO, GAS ENGINE, NEW REAR WHEELS AND TIRES, ENGINE RUNS.
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|