Tractor Talk Discussion Board |
Re: 12 or 24 volt?
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by txblu on February 22, 2005 at 05:19:10 from (209.151.113.162):
In Reply to: 12 or 24 volt? posted by fullsircle on February 21, 2005 at 17:36:30:
Agree with buickanddeere on the "line running amps" thing. My newly acquired 4230 has 2 six volt batteries in series with one on one side of the tractor (grounded there) and wired to the other side picking up the second battery and the output of it connecting to the starter. Engine turns over slowly for a big diesel you want to start. Wire size looks to be 2 AWG (too small for me). Now on the other hand, I have 2 12v batteries sitting adjacent to my 24 volt starter on my 4010 (rig I made) and had the same type rig on a 4020 I previously owned. Use 00 wire and no piece is longer than 15". Now if you want to see a diesel start on it's own in the winter (30 degr) the 10 will do it; only cause it's spinning up.....naw, it's screaming. So, next year, I am going to pull out the 6 volt batteries and wire in 2 12v with parallel wiring, size 00 all the way. I know it will make a difference, but not equal the 24 volt rig. Is your starter still functional? I bought a 24 volt gen from the www (don't remember if it was from Walt's or not, may have been from an importer/exporter in New England). Anyway I'm recalling that it was around $85 and got a new regl for around $30 for my '10.....been a couple of years...had no problems since. You can redo the starting solenoid yourself by opening it up and doing some housekeeping on the big copper contacts. $ 539 is a lot of bread. I'd be inclined to think about it and do some lookin. HTH Mark
Follow Ups:
Home
| Forums
Today's Featured Article -
My Ford Golden Jubilee - by Troy Estes. This article is about my '53 Ford Jubilee and a story that starts with taking the tractor to my brother's Starter/Alternator Rebuilding shop for a wiring fix. The generator was shot as well as all the wiring. I dropped off the tractor expecting a transformation from a 6 volt to a 12 volt system utilizing the original generator housing, and a total rewiring of the whole tractor. The front end center pin bushing was worn also so I ask that they replace it if they had time. Well, that’s wha
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2025 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|