|
Tractor Talk Discussion Board |
Re: Another OT; Main entrance gate intercom
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Mark - IN. on January 04, 2005 at 20:44:43 from (64.12.117.7):
In Reply to: Re: Another OT; Main entrance gate intercom posted by Mark - IN. on January 04, 2005 at 20:21:26:
Many years ago at a army installation in Germany, I ran a pair of wires about two miles from a building to a gate for a ringer so didn't have to post a guard around the clock at the gate to let an occasional guest in. Took the pair of wires and ran them to 110/120VAC. The hot side of the AC ran out to a spring loaded switch at the gate (had a sign saying "press button to be let in") through one of the wires, through the switch, back to the building on the other wire, into a telephone on the tip side (green wire). The neutral (other) side of the 110/120 AC went into the ring side (red lead) of the telephone. When the button was pushed, completed a 110/120 VAC circuit through the bell of the phone, making it ring for as long as someone held the button down. AC is not polarized, so could actually reverse the wires and would do the same thing. The point is that had to send AC out to one side of the "spring loaded momentary" switch on one wire, back to one side of the phone ringer on the other wire from the other side of the switch, and the other side of the AC had to go to the other side of the bell. Press the button, phone (bell) rang, then drove out there in a jeep and opened the gate. You could do that, but make sure that the AC source and cable are properly fused, because lightening just loves shallow cable. If you bury a cable, should be 24 or 22 Ga PIC (gel filled buried drop), should be a foot deep at least, and don't forget where buried it - and probably isn't code for civilians. In the army, we didn't care about code or regulations, we just did what had to be done, and kept our mouths shut.
Follow Ups:
Home
| Forums
| Order Support
Today's Featured Article -
Talk of the Town: Diesel Vs. Gasoline - by Staff. Another neat discussion from the Tractor Talk Discussion Forum. The discussion started out with the following post: " I am in the market for an older tractor (to be read... cheap). I have been told a diesel holds up better than a gasoline engine as far a wear, tear, neglect and abuse. Since I am looking at older tractors that have probably been through it all, is it better to buy diesel? I do expect to have to do a good bit of work on
... [Read Article]
Latest Ad:
For sale Farmall super A tractor is complete and has just been setting for awhile,it was running when pulled out of the barn,shouldn’t take to much to get it going asking 1100.00
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|