|
Tractor Talk Discussion Board |
Re: OT Ford Escort Head
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Mark - IN. on December 11, 2004 at 05:45:39 from (64.12.117.7):
In Reply to: Re: OT Ford Escort Head posted by RN on December 10, 2004 at 21:38:11:
I do believe that you're all correct. Never dealt with an Escort, but mechanicals are all the same. I like those readings, tapering right off from the cam pulley. Those readings are a story book themselves. Head might be alright, might be scrap. I would imagine block's aluminum too. Well, certainly don't have to pull the motor to replace the head gasket - just the hood to get at it properly, and may not even have to do that (never touched an Escort). I would imagine going to have to take the cover off of the motor for the serpentine belt that drives the cam because going to have to time it after put back on (doubt seriously has a chain, gotta be a belt). Check the idler pulley between cam and crank pulley to make sure is good before button up. Take that head down to a machine shop and have it checked and/or decked if needs it and is cheaper than buying a replacement. If need a replacement, I'd be leary of buying from a bone yard since are probably throw away's, as someone else said, and that's probably one of the reasons ended up in a bone yard to begin with, and would certainly have to be checked/decked as well. That's pretty interesting that compressions drop off at the cam pulley in a linear manner like that. Engine overheated? Aluminum block and head expanded, contracted while cooling and now head bolts got loosened by belt movement/vibration? Maybe just a head gasket, but gotta pull the head anyway to replace it, so have the head checked for warpage, and if can be decked (if cheaper than buying a replacement). No big deal if was cast iron block, may not be a big deal for aluminum. Probably got the car cheap, and if have to invest in a head (and just may not), probably still cheaper than buying a new car. A head job aint all that bad. Mmm? Something about those words. Ha Ha Ha Ha.
Follow Ups:
Home
| Forums
| Order Support
Today's Featured Article -
An Old-Time Tractor Demonstration - by Kim Pratt. Sam was born in rural Kansas in 1926. His dad was a hard-working farmer and the children worked hard everyday to help ends meet. In the rural area he grew up in, the highlight of the week was Saturday when many people took a break from their work to go to town. It was on one such Saturday in the early 1940's when Sam was 16 years old that he ended up in Dennison, Kansas to watch a demonstration of a new tractor being put on by a local dealer. It was an Allis-Chalmers tractor dealership,
... [Read Article]
Latest Ad:
one 8n and one 9n tractor. totaly restored,pretty much everything is new. one 6ft blade good shape.
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|