Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: Tricycle tractors---good or bad?


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by wdTom on November 25, 2004 at 08:30:23 from (155.212.223.18):

In Reply to: Tricycle tractors---good or bad? posted by T.B. on November 24, 2004 at 18:06:07:

A narrow front is easier to manuver in a tight area. On rough ground though youhave to pick 3 tracks for the tractor, while on a wide front end you only have to pick two. A wide front will require a larger area to turn and manuver.A wide front end will ride better as each wheel going over a bump only raises the center of the axle half as much as the height of the bump. As for stability, I don't think when it gets right down to it there is much difference. A wide front pivots at one center point as the axle rotates going over rough ground. The only advantage in a wide front is as the tractor is tilted on a hill side the pivot point of the front end is higher, closer to the center of garvity, the narrow front end piviot is the ground so as the tractor is tilted on a hill side the center of gravity swings out farther from the contact of the front end (pivot point) with the ground. Just think of hanging a string from about the center of the radiator, as the tractor tilts the string will swing out remaining verticle and it will be closer to the pivot of the wide front end in the center of the axle than the contact (pivot) of the narrow front with the ground. A wide front end tractor still is supported on only 3 points is what I am pointing out here. If the wide front tractor starts to roll, the wide front axle may contact the frame and maybe prevent it from going, I would not want to count on this though, by the time this contact happens it is probably on it's way as the tractor would be on a pretty steep hillside or grade in the first place, then with the addition of the angle need for the front axle to contact the frame, I think it is going over at this point. I think it comes down to what you like, what you have, or what you can end up with. Unless there are reasons you have for one or the other.


Follow Ups:




Post a Followup

:
: :

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Third Brush Generators - by Chris Pratt. While I love straightening sheet metal, cleaning, and painting old tractors, I use every excuse to avoid working on the on the electrics. I find the whole process sheer mystery. I have picked up and attempted to read every auto and farm electrics book with no improvement in the situation. They all seem to start with a chapter entitled "Theory of Electricity". After a few paragraphs I usually close the book and go back to banging out dents. A good friend and I were recently discussing our tractor electrical systems when he stated "I figure it all comes back to applying Ohms Law". At this point ... [Read Article]

Latest Ad: John Deere B 1943 [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy