Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: how much can a person lift with a Farmhand F11


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Allan in NE on September 11, 2004 at 10:24:10 from (148.78.243.25):

In Reply to: Re: how much can a person lift with a Farmhand F11 posted by hagan on September 11, 2004 at 08:18:31:

I would bet a guy can still get the mounts from the company right down here in Colorado. I think, if I'm not mistaken, that they are now owned by AGCO.

Trouble is, that big mount has still got to be trussed up to the front of the tractor. I always ran at least a 3/4" truss rod and cinch eye from the box mount under the rear axle up to a plate where the braces come down from the upper rear corners and where they bolt to the tractor's frame rails.

That way, the "acquired load" is placed across the entire tractor instead of just placing it square in the tractor’s center point. Not pretty when they split.

Another thing about the F-10 is that they can develop a somewhat annoying and dangerous sideways "sway".

I countered this by running some braces made of 3/8 X 2" flat iron, about 25 to 30" long, across the upper corners. Angled from the upper arms over to and bolted to that large rear upper cross member. Just makes 'em "stout" for heavy work just as you are planning.

I dunno, I'd sure think about one of these guys; they were made for heavy work and if a guy can get past the mental block of the tractor being "inside" the loader, they make for a very handy and durable workhorse. Plus, as an added feature, they have that sweet "all in one" rotating hydraulic control valve.

I think it is just what you need for those heavy guys you are working with.

Hope ya get 'er figured out.

Allan



Follow Ups:




Post a Followup

:
: :

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - The Engine Rebuild Kit - by Curtis Von Fange. I always liked engine rebuild kits. They have all the replacement parts for overhauling an engine without going to the store to get gaskets, special measuring tools, or miscellaneous parts. They come neatly packaged, clean and tidy. But it's important not to let that packaging lull you into a false sense of security. The appearance of matching sleeves, pistons, rings, and bearings can cause frustration and agony if not properly measured and installed in a workshop environment. Following c ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy