|
Tractor Talk Discussion Board |
Re: Fence posts in sand
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Jon C -Florida on September 07, 2004 at 16:34:22 from (66.209.40.195):
In Reply to: Fence posts in sand posted by Mark - IN. on September 07, 2004 at 16:08:54:
Mark - Assuming you have fine sand , one way of getting piles set in Florida is to "jet" them. We take a gas engine driven pump, and using about a 3/4" p.v.c. wand, about 6 to 8 feet long, use water under pressure to sink the pile. The wand is just clamped to the discharge line of the pump, and standing the pile/post up where you want it (remove the top soil), you blast around the base of it, displacing the sand. The pile will drop into the displaced "quick" sand, as the sand slurry washes to the surface. You control the depth with the pvc wand. Keep moving the wand, lifting and probing around the post. When set, just pack the sand slurry around the post and let the water drain down. Your only problem will be a source of water. But assuming you have a water tank and a small (1-2 h.p.) pump, you can set a load of posts in a hurry. We use it for dock building, and even the initial setting of bridge piles, before the driving process starts. I have "jetted" some rather large piles (telephone poles) by hand for docks and moorings that I built, and I have seen huge concrete piles jetted up to 20 feet deep with a crane and a much larger pump. We generally only wet sand to avoid getting stuck in dry powder "sugar sand" down here, but just wetting usually does not work too well in a post hole without using the jetting process. I have no idea if it will work up in your country...but if the sand is fine enough, you might want to give a try.
Follow Ups:
Home
| Forums
| Order Support
Today's Featured Article -
Gettin My Old Tractor Home - by Clayton Sweeney. My name is Clayton Sweeney. I am from Southern Maryland in a small town called Lothian. I am 20 and my father and I are the proud owner of a 1954 Allis Chalmers WD-45. When I was 18, I dated a girl in the next county over. Her family are tobacco farmers. It was a cold Thanksgiving evening, and we were going up to her Grandparents house. As we passed one of their barns, I noticed something orange in the corner of my eye in this old shed. It was pretty dark and I asked what it was
... [Read Article]
Latest Ad:
1965 International Harvester McCormick Farmall cub tractor 2,500. Two owner tractor. My grandfather bought new in 1966, then we inherited it. Have all the paperwork original manual and all maintenance records. It starts and moves. Comes with underbelly mower, plough, and some other attachments.
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|