Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: Re: Re: Re: Re: Re: Re: winch wiring


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by txblu on July 28, 2004 at 06:07:00 from (199.46.199.233):

In Reply to: Re: Re: Re: Re: Re: Re: winch wiring posted by john in la on July 27, 2004 at 10:13:36:

That's interesting John because a crane/dragline is just what I was thinking about. Draglines I've seen lift a 5 cu yd bucket of sand with a 3/4" cable. Have about 8 trips thru the pulleys.

5 yd bucket at 5k lbs (guess)
5 yds sand @ 4k/yd 20k lbs

Total 25k lbs.

TSC 3/8 wire rope rated around 2k lbs (just bought some). Area = .108". 3/4 dragline cable is .441" area or 4:1. 2k x 4 is only 8k load rating for cable; load is 25k. But 8 trips is 25/8 = 3.1k. Nice safety factor. Looks like the designers did their job.

Hmmmm.


Besides, when I added the block, my arm knew that the winch cable didn't see the whole load cause I could now lift it quite easily whereas before I couldn't and nothing else changed except cable diam and that had nothing to do with what my arm felt.

These things were majestic and must have been 40 yrs old. They'd sit on the side of a sand pit and the operator was so good he made a seamless pattern in the sand, came up with the bucket and dropped it into a dump truck/pup combo and dropped nar a bit on the ground. Now for those uneducated, the pup is about the same size as the bucket that is swinging below the crane and the bucket is swinging towards it; never stops, seamless tapistry...Real artist. Course inside the engine room was clank, clatter, squeak. hummm.

I'd bet you were that good.

Mark


Follow Ups:




Post a Followup

:
:

: Re: Re: Re: Re: Re: Re: Re: Re: winch wiring

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Engine Valves - Some Helpful Information - by Staff. Intake - On the intake stroke the piston moves doward, sucking in carburized fuel through the open intake valve. Exhaust valve is closed. Compression - With both the intake and exhaust valves closed, the pistons upward stroke compresses or squeezes the fuel into the combustion chamber. Firing - Ignited by the spark, the compressed fuel explodes and forces the piston downward on its power stroke. Intake and exhaust valves are closed. Exhaust valves and seats are exp ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy