|
Tractor Talk Discussion Board |
Re: follow up on 5th wheel hitch location
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by T_Bone on July 02, 2004 at 22:18:42 from (4.240.132.201):
In Reply to: follow up on 5th wheel hitch location posted by Duane on July 02, 2004 at 21:28:26:
Hi Duane, From all the install manuals I've read, most state there's less than 1% front axle loading difference from 4" behind to 4" in front of the axle. From a optimum pulling stand point, axle center line to forward of axle center line pulls best. If you want to see in writing what the Dealer is told to install too, including drilling holes and where you can drill those holes, framing welding, etc; can be found on the Ford commerical truck website titled "Ford Body Builders Handbook" For 2005 Ford has changed several items on the F250 to F550 spec's. I just repeating what I've read on different websites and not from Ford other than when Ford was direct quoted; Frames on the F250/F350 SWR has changed to a heavier frame to be rated at 23,500 GCWR, tops in the industry. 4wd drive axles on the F250/F350 SWR are now a coil frame attached attached by a strut to the frame, simular to Dodge, which was a night mare the first few years for Dodge (weak design) F350/F450/F550 DRW will still use the leaf spring mounting on 4wd, much stronger design of Fords past. Both Dodge and Ford Both look the same and if Ford took off the "blue Oval" in the center of the grill, it's close to a Dodge look. That was the only differences I was looking at as I'm sure there's more. You would need the builders handbook for your model year, not 2005 which may be why Ford has changed mounting deminsions. I've seen the 2003 manaul and your good there before the axle as in previous years but I haven't looked at a 2004 manual. T_Bone
Follow Ups:
Home
| Forums
| Order Support
Today's Featured Article -
A Tractor's Point of View - by John Manley. I began my life on August 3,1941. I was actually built at different times and days but I was officially an M Farmall on August 3.I was real nice and shiny. That�s me, in the old picture, third from the left. I was loaded on that train and sent to a little town in South Carolina. I didn�t get to see much of that town. I was moved off the train fast and on to the dealer�s
... [Read Article]
Latest Ad:
1958 FORD RARE 4x4 801 TRACTOR, ELENCO/FRONT DRIVE, FRONTLOADER AND WEIGHTED REAR WHEELS, FIVE SPEED, LIVE PTO, GAS ENGINE, NEW REAR WHEELS AND TIRES, ENGINE RUNS.
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|