|
Tractor Talk Discussion Board |
Re: Longest running production tractor
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by JT on June 02, 2004 at 23:52:50 from (206.72.54.246):
In Reply to: Longest running production tractor posted by Don Wadge on June 02, 2004 at 11:22:23:
Dan I think you took offense when none was intended. I will stand by my earlier statement about the basic design of the D and 830 being the same though. When you break it down I beleive it makes sense. The early D's were 2 speed had a two cylinder cross mounted engine over center hand clutch in a pulley on the right. Later D's had a three speed trans all else was the same. The R had a trans which was a 6 speed I beleive with a HI/LO gearset to obtain the extra speeds live hyd and pto (all to meet market demand) motor clutch layout is still the same. The 80 was a R with power steering and a different starting engine. The 820 may have had a hydraulics change (I know the row crop 20 series did) otherwise the only thing that changed was HP and paint. Hp and sheet metal was the only improvement on the 30 series still had the crossmount 2cyl engine with overcenter hand clutch on the right just like the spoker D did. I would group a 29 Case L in the same group with a 600. As a IH 560 with a 39 M. As a JD 3010 with a 4860. Not that there is anything wrong with the design of any of these tractors actually it shows the forsight of the people that started with a blank sheet on all of these that the run of the design lasted so long. When a 830 and a early D are put next to each other there are a lot of differences yes but the basic layout is the same. I beleive this is apperant when you compare the 830 to the 820, the 820 to the 80 and so on back to the early D. Admitadly this is my opinion but it goes to show that when you have something that works you don't mess with the basics just add what is needed. JM2CW JT
Follow Ups:
Home
| Forums
| Order Support
Today's Featured Article -
Trailering Your Tractor - by Curtis Von Fange. One of the fun things of summer and fall are the parades and tractor shows that go on across America. Many owners of tractors travel long distances to attend these shows and they usually take their restored iron along with them. Safe trailering practices and inspections will ensure that the event is a fun one. A good habit to develop when using a trailer is to give that �quick look over� before taking it on a trip. Before hooking up to it check the tongue for proper operation. The latche
... [Read Article]
Latest Ad:
1965 International Harvester McCormick Farmall cub tractor 2,500. Two owner tractor. My grandfather bought new in 1966, then we inherited it. Have all the paperwork original manual and all maintenance records. It starts and moves. Comes with underbelly mower, plough, and some other attachments.
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|
