|
Tractor Talk Discussion Board |
Re: Kinda OT, But how much gravel do I need?
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by EngineerJoyce on March 25, 2004 at 17:51:37 from (67.232.144.141):
In Reply to: Kinda OT, But how much gravel do I need? posted by Matt on March 25, 2004 at 16:23:15:
Most important: USE GEOTEXTILE!!!!! On top of the bare dirt before the first shovel full of gravel, put geotextile on the driveway and put the rock on top of the geotextile. The trucks driver should be capable of "back dumping" - or dumping the rock as he backs down the driveway, not driving directly on the geotextile. Geotextile keeps the rock "floating" on top of the dirt. Since rock is heavier than dirt, the natural order of things is for the rock to sink down into the dirt like water, only slower. By putting the geotextile barrier between them, you keep your rock where you want it - on the surface. Using the geotextile will prevent potholes and soft spots and you will NEVER have to add more rock - unless it gets washed off or something. Geotextile usually comes in 9', 12', and 15' widths. The 9' would be acceptable, but the 12' will give you more "breathing room". 210' x 12' x 4" will make about 60 tons. Add more for a turn-around, about 30x30 for nearly another 20 tons. Geotextile can be found at most any construction supplier and lots of Agriculture suppliers. An internet search will yield lots and lots of hits. Any rock you put down on top of dirt, put geotextile down between them. Anywhere.
Follow Ups:
Home
| Forums
| Order Support
Today's Featured Article -
Tractor Traction - by Chris Pratt. Our first bout with traction problems came when cultivatin with our Massey-Harris Pony. Up till then, this tractor had been running a corn grinder and pulling a trailer. It had new unfilled rear tires and no wheel weights. The garden was already sprouting when we hooked up the mid-mount shovel cultivators to the Pony. The seed bed was soft enough that the rear end would spin and slowly work its way to the downhill side of the gardens slight incline. From this, we learned our lesson sinc
... [Read Article]
Latest Ad:
WANTED Front grille/nose assembly for Massey Ferguson 1160 (also fits 1180 & 1190). Headlight-mount section. AGCO Grille 3706022M91 (supersedes 3705942M91), cover 3705494M1/M2, holders 3705501M91/3711158M92. New/NOS/good used OK. Jonesboro, AR - will pay shipping. Photo appreciated. Thanks
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|
