Tractor Talk Discussion Board |
Farmall Cub and belly mower
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Fritz Campbell on March 14, 2004 at 17:07:05 from (198.77.40.99):
Every year about this time - I start thinking about getting ready to mow the grass - although I'm a month or so early. My two JD 140 mowers are ready for the mowing chores (I alternate them every other week) and they do a great job on my 1 1/2 or so acres of grass. I don't rush my grass mowing and it takes me approx 3 hours to mow it all with their 46" decks. I have some areas that I'm particular about and some that I'm not - but I like to keep it mowed [I don't mind snakes as long as I don't see them laying around]. I have a 4' brush hog on my New Holland compact and use it for monthly mowings on the walking trails. I use the brush hog on the places I'm not particular about, I keep the blades pretty sharp and it does a decent job but its rough and the lower I keep the cut the more I tear up the ground with it. I think I need something in between and that is what I'm getting too. Would I be happy with a smaller farm tractor i.e. Farmall Cub or an A with a 5' belly mower as a decent grass cutter? I could use my 140 and push mowers around the "lawn" and mow the "yard" with the bigger belly cutter and cut my mow time down some. Some weeks when I'm lacking for time maybe I could mow everything with the 5' cut(last summer I was mowing every 4 days to keep ahead - wettest summer on record here in PA). My neighbor has a '49 Cub with a Woods belly mower and uses it in his field for rough cutting. I have observed the cut quality and it doesn't look bad. He doesn't use it around the house because his yard is really steep and odd shaped. I have some slopes on mine too but most of it is wide open. Every time I look at the disposable lawn tractors I get to thinking that for almost the same price I could pick up something with a Woods belly mower - keep it nice and have it for a long time. Sorry for the long question - just looking for some advice. Thanks!!
Follow Ups:
Home
| Forums
Today's Featured Article -
The Nuts and Bolts of Fasteners - Part 2 - by Curtis Von Fange. In our previous article we discussed capscrews, bolts, and nuts along with their relative hardness and thread sizes. In this segment we will finish up on our fasteners and then work with ways to keep them from loosening up in the field. Capscrews, bolts and nuts are not the only means of holding two parts together. When dealing with thinner metals like sheet tin, a long bolt and
... [Read Article]
Latest Ad:
Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|