|
Tractor Talk Discussion Board |
Re: Re: Re: 4020 hydraulic problem?
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Mark on March 13, 2004 at 06:54:35 from (209.151.113.248):
In Reply to: Re: Re: 4020 hydraulic problem? posted by Ray on March 13, 2004 at 05:15:55:
The 4020 uses a demand type system for remotes. The system pressurizes to 2500# and sits there. When a drop in pressure is detected (you opened a valve to raise the arms) the pressurization system responds until pressure is reestablished....at something like 24 gpm...that's a lot of fluid flow. There isn't any continuous fluid movement (like Ford) unless you tell the system to do some work. That is why you use a CLOSED CENTER on green and OPEN CENTER on blue. You should have a closed center dual 2 way valve to control your loader (2 supply lines and 4 load lines). Each side has a center position (spring loaded) and a forward and reverse. The system is set up for 2 way cylinders so that you can force the hyd. cylinder in either direction...you can lift a bucket full of dung or push down, raising your front tires off the ground and fix a flat. When you pull the control piston out of the valve body toward you the front hose is activated and pushing is the converse. This is where you want to do the swapping as it is the easiest spot. Each line should have a swivel on at least one end. The other is usually just a male 1/2 pipe plug. The main valve body has two side ports (Cross does), one inlet marked IN and the other return (to the tractor sump). This fluid flows the same way all the time only when a valve is activated. While one port of your 2 way valve is letting pressurized fluid into the cylinders you want to operate, the other half of it is letting fluid out of the hyd. cylinder so that it's position can be changed. If you get any air in the sytem, just work the controls back and forth a half dozen times and it will purge it'self. Mark
Follow Ups:
Home
| Forums
| Order Support
Today's Featured Article -
Tractor Traction - by Chris Pratt. Our first bout with traction problems came when cultivatin with our Massey-Harris Pony. Up till then, this tractor had been running a corn grinder and pulling a trailer. It had new unfilled rear tires and no wheel weights. The garden was already sprouting when we hooked up the mid-mount shovel cultivators to the Pony. The seed bed was soft enough that the rear end would spin and slowly work its way to the downhill side of the gardens slight incline. From this, we learned our lesson sinc
... [Read Article]
Latest Ad:
1965 International Harvester McCormick Farmall cub tractor 2,500. Two owner tractor. My grandfather bought new in 1966, then we inherited it. Have all the paperwork original manual and all maintenance records. It starts and moves. Comes with underbelly mower, plough, and some other attachments.
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|