|
Tractor Talk Discussion Board |
Re: Re: Re: couldn't pick up the bale
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Mark on February 01, 2004 at 06:34:48 from (209.151.112.101):
In Reply to: Re: Re: couldn't pick up the bale posted by Joe on February 01, 2004 at 06:17:22:
I've got to jump on this. I'm a city boy gone to urbania 25 years ago. Had a slick little IH 454 @45 PTO hp and really low hrs. Got some cows and needed hay. Contacted custom baler and did the lot next door....beautiful BIG round bales (5x6 as I remember). Built me a hay spike and here we go. Backed up to the bail, hit the lift and presto the bale stays on the ground and the front end becomes airborne. 500# of railroad rails and a front bracket later and I can haul hay.
The other side. Had (still do) early vintage '60's Fords which needed the same front end weight but these all (3) had different kinds of hydraulic problems which I attempted to fix over the years. The best Is a little 2000 diesel (smallest of 3) and it picks 5 x 6's right up. Your pump has to be putting out 2500#, your seal on your lift piston has to be in new condition, your pressure relief valve has to be above 2000# and you have to have your RPM's up to keep the fluid flowing and compensating for the leaks. One of my Fords will only lift at PTO RPM, the other one will lift if I get off the tractor and help push the bale up....then It will keep it up (at PTO RPMs). Your idea about smaller bales or larger tractor is the right approach. One thing to keep in mind. Around here they sell bales by the bale not tonnage. Tonnage here is not the way to sell things because the moisture content really screws up the true value of the dry matter. Anyway, they roll 4 x 5 and 5 x 6 bales. Some sell the 4 x 5 for the same price ($25) as others the 5 x 6. If you are the seller.....great. If you're the buyer, there are 1.8 4x6 bales in a 5x6 bale (based on figuring volume of each). I suppose the 4x5 baler was made for the reason you mentioned......can use a smaller tractor and the purchase price (new anyway) is less. Hope this helps. Mark
Follow Ups:
Home
| Forums
| Order Support
Today's Featured Article -
Trailering Your Tractor - by Curtis Von Fange. One of the fun things of summer and fall are the parades and tractor shows that go on across America. Many owners of tractors travel long distances to attend these shows and they usually take their restored iron along with them. Safe trailering practices and inspections will ensure that the event is a fun one. A good habit to develop when using a trailer is to give that �quick look over� before taking it on a trip. Before hooking up to it check the tongue for proper operation. The latche
... [Read Article]
Latest Ad:
1965 International Harvester McCormick Farmall cub tractor 2,500. Two owner tractor. My grandfather bought new in 1966, then we inherited it. Have all the paperwork original manual and all maintenance records. It starts and moves. Comes with underbelly mower, plough, and some other attachments.
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|