|
Tractor Talk Discussion Board |
Re: Generator
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Bob M on January 28, 2004 at 07:59:34 from (165.170.128.65):
In Reply to: Generator posted by Walker on January 27, 2004 at 18:46:10:
Walker - Problem could be one of several possible causes: 1 - May be the battery is fully charged and the regulator is simply doing it's job. If a voltmeter is placed across the two battery posts and it indicates 7.2 volts or higher while the ammeter shows 10 amps, there is no problem! 2 - High resistance in the wiring between the generator "A" terminal and the battery. Use an accurate DC voltmeter and take a voltage drop measurement between the generator "A" terminal and the ungrounded battery post with the engine running at full RPM. A reading greater than about 1/4 volt says there's excessive resistance in the circuit. Look for bad connections, undersized wiring, etc. 3 - 3rd brush set to low. Readjust it to it's maximum current position - so 3 commutator bars are showing between the 3rd brush and the nearest fixed brush. Keep in mind most 3 brush tractor generators are only designed for about 14 amps max output. Higher output can cause overheating and damage. 4 - The armature has one or more shorted or open windings. If the generator gets hot to the touch after running about 15 minutes, or if the enamel insulation on the armature windings appears baked/burned, the armature has an internal short. An open winding can be found by probing the commutator with an ohmmeter. Either condition requires rewinding or replacing the armature. 5 - (long shot...) Could be a high resistance ground at the regulator. Note to Pappy - 6 volt IHC tractors built after about 1949 or 1950 use a 3 brush generator with a 2 element voltage regulator in place of a cutout. Pretty sure other tractor builders using Delco electrics did the same.
Follow Ups:
Home
| Forums
| Order Support
Today's Featured Article -
Harvestin Corn in Southern Wisconsin: The Early Years - by Pat Browning. In this area of Wisconsin, most crops are raised to support livestock production or dairy herds in various forms. Corn products were harvested for grain, and for ensilage (we always just called it 'silage'). Silo Filling Time On dairy farms back in the 30's and into the first half of the 40's, making of corn silage was done with horses pulling a corn binder producing tied bundles of fresh, sweet-smelling corn plants, nice green leaves with ear; the
... [Read Article]
Latest Ad:
For sale Farmall super A tractor is complete and has just been setting for awhile,it was running when pulled out of the barn,shouldn’t take to much to get it going asking 1100.00
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|
