|
Tractor Talk Discussion Board |
Re: O.T. isulation and moister barrier.
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by wdTom on December 27, 2003 at 07:54:49 from (155.212.223.136):
In Reply to: O.T. isulation and moister barrier. posted by Chances R on December 25, 2003 at 07:19:21:
For an old house that can be drafty I would definatly use a vapor barrier. Even if you use karft backed insulation in the walls, which you should do to hole it in place, a vapor barrier can help as there can be leaks or tears in the kraft face. Do the ceiling too. It is easier to vent the space with exhaust fans in the kitchen and bath if necessary than to live with a drafty house or have a moisture problem in the insulation. Do a very carefull job of insulation. If you miss a little corner it can let the cold into that whole section of wall or ceiling. Cut the insulation to fit the space carefully with maybe 1/2" to 1' extra at the ends, you want it to fit, but not compress the insulation. Insulation works because it traps air spaces, if you compress it it has less or no air space in it. You can't have too much atic venting. If you do a good job of insulation, install a vapor barrier, have good venting, you won't have a problem and you will forever be glad you did because it will be easier (cheaper) to heat. Try to get at least R19 in the walls and r 38 or 40 in the ceiling. You can fatten out the studs to be able to get more in walls or you can add a layer of ridgid foam board over the studs. Then the vapor barrier. I have a lot of walls in my house that are double studded and this works great I have found. A double studded wall has two rows of 2 x 4s, the sill and top plate are 2x 8s and the studs are offset from each other by 12", so you have a stud every 12" one on the inside, then one on the outside, etc. along the wall. At windows or doors you use 2x8s to frame the opening. When you put up the outside layer of 4' insulation you must puncture the vapor barrier to allow for moisture to pass out through it. I used a approx. 12" square board with a bunch of nails sticking out through the bottom, a 2x3" handle sticking up. I would just go along the insulation strup before I put it in place and make hundreds of holes in the kraft facing, then staple it in place. You really need the facing in a wall to hold the insualtion, unfaced would sag over time and be worthless.
Follow Ups:
Home
| Forums
| Order Support
Today's Featured Article -
Antique Tractors a Passing Fad? - by Tractor Talk Forum Participants. A Talk of the Town article - Do you see antique tractors going out like a fad? Value has come down this winter. An example is the Ford Model A and T cars that went through this in years ago, along with the hit & miss engine. Will the younger generation move on to something else? Will it be harder to sell them and what models will be affected? Could we see the value crash on our rusty relics?
... [Read Article]
Latest Ad:
Ford 3-Point Single Bottom Moldboard Plow with Coulter
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|