Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: PVC Pipe Instalation


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Phil in MS on December 04, 2003 at 14:00:32 from (207.203.128.29):

In Reply to: PVC Pipe Instalation posted by Alvin Wilkinson on December 04, 2003 at 07:12:55:

Alvin,

A friend and I have laid pvc pipe several times using a subsoiler. First plow your route several times. Then tie a wire to the bottom of your subsoiler. Glue your pipe together and let it set about 5 minutes or so. Tie the big end of the pipe to the subsoiler foot and stuff a rag into the open end to keep dirt out. He did weld a nut or cut a small hole at the bottom of the foot to keep the wire from riding up as the pipe is pulled. Start your tractor moving and let the plow down and the pipe will feed itself. About all the digging you will have to do will be at each end to attach to water source and to attach to outlet. You will be able to pull several sticks without any problem. We put water to my barn and we may have pulled 120 to 130 feet. We also pulled to his barn which was about 350 to 400 feet from his source. I don't recall having a problem but we did do two pulls of about half way and then did a splice in the middle. I don't think you will have any problems unless your real close to several buildings or other obstacles. In North Mississippi you only need to be 10 to 12 inches deep and depending on your plow you should be able to get that deep or deeper. If your in a colder climate you may have problems getting deep enough with just a plow.
Good luck.


Follow Ups:




Post A Followup

:
:

: Re: Re: PVC Pipe Instalation

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Tractor Profile: Allis-Chalmers Model G - by Staff. The first Allis-Chalmers Model G was produced in 1948 in Gasden, Alabama, and was designed for vegetable gardeners, small farms and landscape businesses. It is a small compact tractor that came with a complete line of implements especially tailored for its unique design. It featured a rear-mounted Continental N62 four-cylinder engine with a 2-3/8 x 3-1/2 inch bore and stroke. The rear-mounted engine provided traction for the rear wheels while at the same time gave the tractor operator a gre ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy