|
Tractor Talk Discussion Board |
Re: OTQ - How do you charge a pressure tank?
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by uglyoldfatman on October 27, 2003 at 16:00:59 from (216.190.135.135):
In Reply to: OTQ - How do you charge a pressure tank? posted by Fargo on October 27, 2003 at 07:29:31:
What are you trying to do? Is it water loged? Do you think it just does not have enough pressure? The pressure on your system will be whatever your cut-off pressure is on the pump. To change this you must change the setting on the pressure switch. This pressure should not be much over 45lbs. You can get it too high for your commode valve to work properly. If it is water logged, just cut off power, open drain valve and pull one of the plugs close too the top, so it does not create a vaccume. After tank is drained, close valve, put plug back in, and turn on power. You can also add air to tank, with it full if you have a valve stem installed were one of the top plugs are. Try to stay under 70lbs. and drain off water to get the pressure down to cut-off pressure. This way you can force the level of water down to the proper level. May take more than a few times of airing up. Water level should be about the lower 1/3, as long as it is above the inlet point. You can tell the water level by running your hand up and down the side of the tank. There will be a differance in the temp. of the tank, at the water level. If you have a submerged pump, there is a valve (2) that goes about 12-15 ft. down the pipe, that drains the water out of the pipe when the pump is off, so that every time the pump comes on, it will force air in the tank, and keep it from water-logging. There is a check valve in the tank on this system. Hope this will help. UG!
Follow Ups:
Home
| Forums
| Order Support
Today's Featured Article -
Tuning-Up Your Tractor: Secondary Ignition Wires and Distributor - by Curtis Von Fange. In our last episode we spent the entire day checking out the spark plugs. Is that efficency? Actually, it took more time to explain than it really did to do the inspection. At any rate we decided that a compression test was in order so we could verify the internal engine status. That way we wouldn't buy any tune up parts until we were sure that the engine was in reasonable mechanical condition. Our tests showed a fictional compression reading of 85, 80, 82 and 86 psi. That is well within a
... [Read Article]
Latest Ad:
1958 FORD RARE 4x4 801 TRACTOR, ELENCO/FRONT DRIVE, FRONTLOADER AND WEIGHTED REAR WHEELS, FIVE SPEED, LIVE PTO, GAS ENGINE, NEW REAR WHEELS AND TIRES, ENGINE RUNS.
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|