|
Tractor Talk Discussion Board |
Re: TUBELESS TIRE WATER BALLAST
[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by ERIC on September 21, 2002 at 12:13:56 from (198.149.7.1):
In Reply to: TUBELESS TIRE WATER BALLAST posted by Ken McWilliams on November 24, 2000 at 11:17:16:
AFTER READING AND TALKING TO LOTS OF FOLKS ABOUT AN ENVIRONMENTALLY FRIENDLY AND INEXPENSIVE WAY IN THE LONG RUN TO ADD WEIGHT TO MY TRACTOR I HAVE COME TO THIS CONCLUSION. TUBLESS TIRES FILLED WITH AIR, NOT FLUID FILLED WITH CORROSIVE OR TOXIC FLUIDS, WITH WHEEL WEIGHTS ADDED SEEMS TO MAKE THE MOST SENSE. THE ONLY MONEY I AM OUT IS THE COST OF THE PLUG KITS TO PATCH MY FLATS AND THE INITIAL COST OF THE WHEEL WEIGHTS THAT I WILL HAVE FOREVER, AND THE TIME FACTOR/VALUE THAT MY TRACTOR IS NOT WORKING. THIS TIME FACTOR IS USUALLY VERY SHORT BECAUSE I DO NOT HAVE TO TAKE THE TIME TO REMOVE THE WHEEL, DISMOUNT THE TIRE, PATCH OR REPLACE AN EXPENSIVE TUBE, REMOUNT THE TIRE, AND REPLACE EXPENSIVE FLUID. ALL I HAVE TO DO IS PLUG THE TIRE IN THE FIELD AND GET A COMPRESSOR OUT TO THE TRACTOR TO AIR UP THE TIRE AND MY TRACTOR IS WORKING AGAIN. IF YOU ARE LIKE ME YOU CAN FIND ITEMS TO GIVE YOUR TIRES PUNCTURE WOUNDS IN THE MOST UNLIKLY PLACES. IF I CAN GET MY TRACTOR MOVING AGAIN IN A HALF HOUR OR LESS THEN I HAVE SAVED TIME AND MONEY BOTH NOW AND IN THE LONG RUN. THE ONLY THING I DO NOT HAVE IS AN EASY WAY TO ADD OR SUBTRACT WEIGHT TO THE REAR WHEELS. THE SUIT CASE WEIGHTS FOR THE FRONT ARE FAIRLY EASY. HAS ANYONE INVENTED AN EASY TO USE MOUNTING SYSTEM FOR REAR WHEEL WEIGHTS? I WOULD LOVE TO BUY ONE OF THOSE. THEN I WOULD BE SET. IF SOMEONE SEES A FLAW IN MY REASONING PLEASE CORRECT ME IN THE INTEREST EFFICIENCY. P.S. MY TIME OF EXPERIENCE WITH TUBLESS REAR DRIVE TIRES IS SHORT. CAN ANYONE TELL ME THE DRAWBACKS I NEED TO LOOK OUT FOR IN USEING TUBLESS REAR DRIVE TRACTOR TIRES? THANKS ERIC
Follow Ups:
Home
| Forums
| Order Support
Today's Featured Article -
History of the Field Marshall Tractor - by Anthony West. Any restorer who has some knowledge of turn of the century farm machinery, will recognize the name Lanz Bulldog!! This machine was to say the least unusual in its appearance. The huge flywheel and coffee percolator shaped exhaust. Along with square body lines and cylinder head protruding forward of the front axle. Would become the visual differentiation that people would quote to separate the Lanz from other period machines. The Marshall company based at the Briannia Works in Gainsborough
... [Read Article]
Latest Ad:
1958 FORD RARE 4x4 801 TRACTOR, ELENCO/FRONT DRIVE, FRONTLOADER AND WEIGHTED REAR WHEELS, FIVE SPEED, LIVE PTO, GAS ENGINE, NEW REAR WHEELS AND TIRES, ENGINE RUNS.
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|