|
Tractor Talk Discussion Board |
Re: international 56 planter
[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Michael Soldan on April 19, 2002 at 19:05:18 from (216.46.130.62):
In Reply to: international 56 planter posted by IH puller on April 19, 2002 at 18:18:00:
I_H Puller. the model 56 runs off of a type one hydraulic ram. When you lift the seeder for the first time there should be a couple of steelstraps bolted through the frame to keep the seeders up when in storage. You will need to raise the planter with the hydraulics and then remove these straps so you can lower it all the way( between the fertilizer boxes). The planter has markers which you undo and let down( unhook the chains) One will go down the other will remain upright until you drop and raise the planter then the chain will reverse and the opposite marker will remain upright. You will need to connect the drive chains on the axles, one on each side and flip the tighteners back. Now the planter will be ready to sow as soon as you drop it into the ground. Any utility tractor with a remote to raise and lower the planter will work. You can move along at a good speed. I don't sow fertilizer with mine, I use a spreader. You can adjust the depth you are sowing at by pulling the pin on the seeder and moving it up or down the series of holes keeping all four seeders set at the same hole. My old 56 works well and I use it to sow sweet corn. I never had a manual and a friend lent me his so I photocopied it but I think your Case I-h dealer can still get you a copy. Incidentally I bought mine at a farm sale and I gave $350CDN for it, was one other guy seemed to want it badly. It is in good shape but needs new shafts in the fertilizer boxes. I'd rather use my 3point hitch spreader anyway. Good luck from Mike in Exeter Ontario
Follow Ups:
Home
| Forums
| Order Support
Today's Featured Article -
Tuning-Up Your Tractor: Secondary Ignition Wires and Distributor - by Curtis Von Fange. In our last episode we spent the entire day checking out the spark plugs. Is that efficency? Actually, it took more time to explain than it really did to do the inspection. At any rate we decided that a compression test was in order so we could verify the internal engine status. That way we wouldn't buy any tune up parts until we were sure that the engine was in reasonable mechanical condition. Our tests showed a fictional compression reading of 85, 80, 82 and 86 psi. That is well within a
... [Read Article]
Latest Ad:
1958 FORD RARE 4x4 801 TRACTOR, ELENCO/FRONT DRIVE, FRONTLOADER AND WEIGHTED REAR WHEELS, FIVE SPEED, LIVE PTO, GAS ENGINE, NEW REAR WHEELS AND TIRES, ENGINE RUNS.
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|