|
Tractor Talk Discussion Board |
Re: Custom work
[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by JWC on March 27, 2002 at 06:41:35 from (130.74.184.124):
In Reply to: Custom work posted by Mike on March 26, 2002 at 17:53:54:
Mike,
A couple things enter into the custom rate. First what size tractor do you have, a small compact with a 4' cutter will not do the same amount of work as a 50hp with a heavy 6' cutter. Secondly your level of experience will determine how productive you will be and what jobs that you take and leave alone. I do brush hogging, and dirt moving work when I have extra time. Brush hogging may range from pasture clipping to moderate briars and small brush to rough terrain and saplings the size of your arm. I have two different size tractors and two sizes of cutters and use and price according to the job. I also have one tractor with a loader and a 6' box blade and a heavier tractor with a heavy-duty 7' box blade the same applies here. For larger cutting jobs the rate is $35 per hour for lighter work and goes up to $60 per hour for the rougher higher risk work. For small jobs (most require 5 to 15 miles of hauling each way) I charge $50 for the first hour and $35 per hour after that (clock starts when the tractor comes off the trailer). For the higher rates I am usually working on slopes that are not for the inexperienced or faint-hearted. As you start out be careful not to let your promises overstep your abilities or equipment capabilities. Be fair and modest with your pricing and strive to do the best job that can be done and most people will happily pay the value of the job. Many folks will add a gratuity for the extra effort to please them. Some folks will not be happy regardless and you refrain from dealing with them again. People tend to pass on the name of the people who do the Best and the Worst jobs. Best of Luck
Follow Ups:
Home
| Forums
| Order Support
Today's Featured Article -
My Ford Golden Jubilee - by Troy Estes. This article is about my '53 Ford Jubilee and a story that starts with taking the tractor to my brother's Starter/Alternator Rebuilding shop for a wiring fix. The generator was shot as well as all the wiring. I dropped off the tractor expecting a transformation from a 6 volt to a 12 volt system utilizing the original generator housing, and a total rewiring of the whole tractor. The front end center pin bushing was worn also so I ask that they replace it if they had time. Well, that�s wha
... [Read Article]
Latest Ad:
1965 International Harvester McCormick Farmall cub tractor 2,500. Two owner tractor. My grandfather bought new in 1966, then we inherited it. Have all the paperwork original manual and all maintenance records. It starts and moves. Comes with underbelly mower, plough, and some other attachments.
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|
