Posted by kcm.MN on November 30, 2021 at 07:41:04 from (174.199.38.165):
In Reply to: Chain saw dressing posted by 550Doug on November 30, 2021 at 06:11:36:
If you're already in the middle of a job, I would not recommend you starting this yourself. Also, would be better to 'learn' on a bar in poor shape while still having a good bar for use.
From your last post about cleaning the gunk, I have to assume that you should probably buy a new chain this time, but do the research and keep up on maintenance. Keep the oiler clear to do its job. Keep the chain sharpened and adjusted.
I know you asked about the bar, but I started using a cheap electric chain sharpener off of Amazon that had LOTS of great reviews. Well, I found out why. I will NEVER go back to sharpening my chains any other way. This sharpener even got better reviews than ALL of the different Stihl brands -- and it's all plastic! Made a world of difference. Best price I see offhand is here:
But sharpening the teeth isn't enough. You also need to file a bit off the height gauges now and then. Lots of videos on Youtube to show how this is done.
From your last post, it sounds like you have used your saw quite a bit without the saw having proper lubrication. So it is very likely that your bar is worn unevenly. Can it be fixed? Probably. No way to tell without measuring the wear. There's also the matter of uneven wear in the slot of the guide rail. If there is side-to-side movement when everything is assembled and tensioned, then there is too much slop in the slot. There should be VERY LITTLE side-to-side movement. No way to make that right either, other than getting a new bar -- which is what I recommend.
You're starting to learn now. That's good. Best to start with new bar and, as you go along, practice on the old bar first. And most of all, pay attention! You'll likely be amazed how easily it all comes together once you know what to keep an eye on.
Upload one or more videos to your post. Photo and video filesizes should be less than 8MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Search For Spares - by Anthony West (UK). Following on from the aquisition of the old Fordson F, I was very much in need of spares. As a novice though I didn't appreciate the fact that there were so many Fordson tractors made, that all the other makes seem rare by comparison. As far as I was aware a fordson was a fordson and it was only through trial an
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
