Posted by 1206SWMO on October 17, 2021 at 14:56:56 from (172.242.195.61):
Yesterday I attended the Crystal estate sale north of Devon,Kansas..It was a little cold in the morning but turned in to a beautiful October day with temps in the mid 60's..There was a nice crowd even with 2 other big sales in the area..The tractors all ran nice and had mostly been used in a cattle operation..The pasture land in these pictures will be cropped next year....Bourbon County Kansas was IH country and back in the day IH probably outsold JD 3 to 1..I had my choice yesterday of burning 30 gallons of gas going to a antique tractor pull in Oklahoma or going to a sale and burning 5 gallons of gas..The sale won out.. The Case-IH CX-100 with loader sold for $26,000...It showed 1234 hours but the front tires were about worn out..? The 1086 IH with a Bush Hog loader sold for $7,900.. The 966 IH sold for $6,100...
The 2 owner 856 IH sold for $6,200....It had been on this farm for 50 years...It once had a cab and loader on it..It had new rear tires..I knew the guy that bought it and that makes him 3 IH 856 tractors. The 1066 IH sold for $6,900..
The 666 IH sold for $5,300....It has the injection pump rebuilt in 2019..
The 2015 Polaris 570 EFI Ranger sold for $8,700...It recently had quite a bit of money spent on it. The 2005 Chevy 1500 4x4 sold for $6,000....It had quite a bit of rust under the doors.
The 2000 Dodge 3500 with older Deweze hydraulic hay bed sold for $8,200...It has a Cummins with a 5 speed. Old non running Chevy 2 ton sold for $550...
Upload one or more videos to your post. Photo and video filesizes should be less than 5MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - The Engine Rebuild Kit - by Curtis Von Fange. I always liked engine rebuild kits. They have all the replacement parts for overhauling an engine without going to the store to get gaskets, special measuring tools, or miscellaneous parts. They come neatly packaged, clean and tidy. But it's important not to let that packaging lull you into a false sense of security. The appearance of matching sleeves, pistons, rings, and bearings can cause frustration and agony if not properly measured and installed in a workshop environment. Following c
... [Read Article]
Latest Ad:
one 8n and one 9n tractor. totaly restored,pretty much everything is new. one 6ft blade good shape.
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
