Posted by Brendon-KS on July 08, 2021 at 05:32:24 from (72.214.204.139):
In Reply to: Re: Right to repair. posted by MarkB_MI on July 08, 2021 at 03:06:52:
The machine I'm responsible for from the engineering side goes a step beyond just publishing the diagnostic trouble codes, we display them right there on the machine's monitor and give a plain English (or whatever language the monitor is set for) description of what it is. There's also a chronological list of past DTC's that is stored in non-volatile memory along with a count of how often each has occurred. This allows you to look up a DTC that flashed on the screen so briefly that you didn't get a chance to read it. But, as you say, the source code for the machine's control software will never be available. When the buyer purchases the machine they are buying the compiled software - they are not buying the un-compiled source code. It's no different than the fact that the purchase of the machine doesn't give the buyer access to all my development work that went into making the final mechanical design what it is. They are buying the final product and that includes the compiled (and thus un-changeable) software that controls it.
True, anyone with a torch and welder can modify the mechanical portion of the machine all they want (it's their machine, after all) but that history is easy to see in the event of product liability or warranty issues. This wouldn't be the case if a controller is flashed with modified software - the original software could easily be re-flashed following an unfortunate incident caused by a rogue programmer and the manufacturer could have a hard time proving it wasn't their fault. I know very well how complicated and intertwined a machine's control software can be and it would be impossible for an outside person to dive into the source code and start making modifications without screwing something up with potentially dangerous consequences. Virtually no software packages that you buy are open source and the machine control software that comes with your new farm equipment is no different.
Upload one or more videos to your post. Photo and video filesizes should be less than 5MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - What Oil Should I Use? - by Francis Robinson. I keep seein this question pop up over and over again in discussion groups all over the web. As with many things there are often several right answers and a few wrong ones. Some purist I'm sure will disagree to no end with what I will tell you but most of us out here in the real world don't really care do we ? Some of them only bring their noses down out of the air long enough to look down them anyway. If you are like me you are only doing this old tractor stuff because you enjoy it. You
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
