Posted by Coonie Minnie on December 19, 2020 at 14:47:41 from (50.123.211.66):
In Reply to: Re: New 5010 posted by svcummins on December 19, 2020 at 12:58:33:
On the 10th of February, 1980, my dad took out a load of manure. Crossing the railroad tracks with the 5020, he was struck by a train. To this day, he doesn't know how he missed the train, but it was only 3 engines and a caboose travelling fast, so he guesses he looked past the train.
The tractor broke in two between the engine and cab... he went out either the front or side window. Two were broke, and he has no recollection of which. He landed in a snow bank, and suffered a separated shoulder. He walked home after the accident, and met the ambulance crew by the mailbox.
He was lucky... one rear tire broke loose from the cast center. His glasses were found under the tire.
The 5020 was a total loss. It had about 10,000 hours already at that point, and had been just overhauled by the Deere dealer. the engine had maybe 20 hours on at most. The tractor was sold for salvage; the spreader (a Deere 680) sat by the tracks or years as a reminder.
That 5020 ran an 8 bottom plow, 12 foot 100 chisel plow, a couple of Fox choppers, etc. Dad really missed it. A 4840 replaced it.
I was in first grade at the time.
Years later, we bought a nearly identical 5020 at a consignment sale in IL. We were looking for a cheap tractor, and nostalgia took over. It had originally been in Ontario. It wasn't nearly the same... it was here until about 5 years ago. I don't miss it- it was fun to run for a bit, but parts were expensive IF available, and it was loud and nobody's favorite. After a soundgard and a turbo, it's hard to go back!
But that 5020 video by Deere took me back to childhood and watching dad with the big plow. That thing was king of the neighborhood in it's day.
Upload one or more videos to your post. Photo and video filesizes should be less than 5MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Tractor Profile: Allis-Chalmers Model G - by Staff. The first Allis-Chalmers Model G was produced in 1948 in Gasden, Alabama, and was designed for vegetable gardeners, small farms and landscape businesses. It is a small compact tractor that came with a complete line of implements especially tailored for its unique design. It featured a rear-mounted Continental N62 four-cylinder engine with a 2-3/8 x 3-1/2 inch bore and stroke. The rear-mounted engine provided traction for the rear wheels while at the same time gave the tractor operator a gre
... [Read Article]
Latest Ad:
Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
