I (retired power distribution engineer) am asking the same type of question as Bob did below. I see 115/230 Phase 1 on the nameplate but read these responses and see wiring diagram, showing TWO L1 connections, and speaking of 208 (NOT 220/240) ?????
208 (as present in 208 Y 120 Volt Three Phase Four Wire Leg to Leg) IS NOT the same as 220/240 in Single Phase 3 Wire
Many non electricians and lay people DO NOT understand the difference in 240 Volt SINGLE Phase, as in typical home 120/240 Volt SINGLE Phase Three Wire service. That's 240 as was 220 or 230 in years past. Its possible to power a 220/240 Volt Single Phase Motor using L1 & L2 as its 240 Volts L1 to L2. Its ONLY 120 either L1 or L2 to Neutral.
VERSUS
208Y 120 Volt Three Phase Four Wire. That's 208 (NOT 220/240).
Of the three L1 L2 L3 legs in the 208Y 120 Volt Three Phase Four Wire Service, its possible to use say L1 to L2 (or L2 to L3) to power a 208 volt rated SINGLE phase motor.
SINGLE PHASE MOTORS REQUIRE TWO HOT PHASE CONDUCTORS (such as L1 & L2) WHILE THREE PHASE MOTORS REQUIRE THREE (L1 L2 L3) Sure, some devices can function on EITHER 208 or 220/240....
NOTE FYI In order to reverse a Three Phase motor (they are self starting) you simply switch/reverse any 2 of the 3 legs.
A Single Phase motor is NOT self starting and requires an out of phase separate start winding. Its the start winding you switch so it starts spinning one way or the other
Nuff said lol and remember NO WARRANTY Im longgggggggg retired from power distribution design and rustyyyyyyyy but believe the above still remains true. Is easier to reverse a three phase self starting motor (swap any 2 legs) then a single phase (start winding)
Upload one or more videos to your post. Photo and video filesizes should be less than 5MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Women and Tractors - Tractor Engine Repair - by Teri Burkholder. One of the great things about working on a tractor engine with your other half is that you know what he is thinking of at all times and can anticipate his every move and his next thought of what he will do. With Ben, anyway, I can tell! He'll be busy working and I�m handing him tools and he says, "give me that..." and I�ve already got it in his hand or "hand me that....."and I�ve got the portable light right where he needed it placed to see. "Run in the house and get me a...."as I open th
... [Read Article]
Latest Ad:
1965 International Harvester McCormick Farmall cub tractor 2,500. Two owner tractor. My grandfather bought new in 1966, then we inherited it. Have all the paperwork original manual and all maintenance records. It starts and moves. Comes with underbelly mower, plough, and some other attachments.
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
