Posted by JDEM on July 21, 2019 at 20:46:57 from (47.33.231.52):
In Reply to: Electrical Question posted by John in La on July 21, 2019 at 15:03:53:
RE your question . . "Without considering the legal side of this how safe or unsafe is this????"
It is absolutely safe, as you described it. That is assuming no mistakes are make, i.e. "human error" while firing up the generator, making sure the main breaker is off, etc.
I doubt you will find anything in writing that specifically states this is "illegal" either, although I know you did not ask about legality. I hear a lot of nonsense and whining about the egregious "backfeeding." The reality is - when done right with no human making errors - it works fine. Is it dangerous considering the lack of redundant safety protection? Heck yes. No question a hard-wired transferswitch eliminates a lot of possible human error. That said, do not make the error and the backfeeding is fine and can hurt nobody.
I still keep a double-ended 50 amp extension cord hanging in my shop. Why? Just in case of a long power outage, I have a hardwired backup 9000 watt generator to give me power (with a transfer switch). If that ever failed, it was the middle of winter and I had to have power? I would just plug in my double-end NEMA 6-50 50 amp cord. One end into a 50 amp welder socket in my barn. Turn off the main 200 amp breaker in the house. Then plug the other end into my PTO 15KW generato and let it power my house. I have done it a few times over the past 50 years and always worked fine. I will do it gain if ever needed - regardless of all the "gloom and doom." It beats having the house freeze up, or having no water. I do not need "Bubba" to help me do it either.
Upload one or more videos to your post. Photo and video filesizes should be less than 5MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - A Farmall Story - by Ed Meadors. The year was 1978. Our young family had recently moved to rural Chesapeake, Virginia to a plot of land which would finally allow us to realize our dreams of a huge garden, critters and more lawn and pasture than we would ever use! We needed a TRACTOR; not a riding mower or tractor wannabe, but a real TRACTOR. The answer to our needs materialized in the form of a '44 Farmall A, complete with cultivators, discs, single plow, a 5ft.Woods belly mower and one, mounted spare 9.00x24 rear wheel.
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
