|
Tractor Talk Discussion Board |
Re: pto driven air compressor
[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Duey (IA) on December 06, 2001 at 17:43:22 from (207.177.85.194):
In Reply to: pto driven air compressor posted by jmyt_47 on December 06, 2001 at 09:27:41:
These are a couple of posts on "How to make an air compressor from a car engine" I read in an old farm magazine some years back, where this farmer converted an old car engine to an air compressor by attaching a pto shaft to the crankshaft and removing the spark plugs. I have forgotten what kind of check valve he had in place of the spark plugs to keep the newly compressed air from returning back into the cylinder. Any info would be appreciated. Thanks, Around here they call them Schrader valves. You take the tappet off of the exhaust valves and leave the valve and spring intact. Leave the intake valve tappet alone so it will suck in air. That way it pumps air on the compression and exhaust stroke both. The way we did it a 4 cylinder datsun engine will fill a 200 gal tank to 150psi in just a few minutes with the pto in high range and the engine at idle. We did'nt put any kind of pressure govornor on it. What we put was a safety pop off valve from a big truck air system on it to keep it at 150 psi. When it hits 150 the safety buzzes the pressure down to about 140 psi but with that kind of volume of air and a 1" air line it will run jack hammers and 1" air reachets with ease all day long. We left the radiator on the datsun so as to keep the compressor cool and filled it with hydraulic oil instead of water so it won't freeze in the winter, we put 80W gear oil in the datsun engine and the datsun turns backwards to a pto so it had to have the pto shaft run to the flywheel end so it would turn the datsun the right way Just be sure and remember to use copper or steel tubing to build your air manifold to the tank because any of the plastc high temp will still melt down.
Follow Ups:
Home
| Forums
| Order Support
Today's Featured Article -
Tuning-Up Your Tractor: Secondary Ignition Wires and Distributor - by Curtis Von Fange. In our last episode we spent the entire day checking out the spark plugs. Is that efficency? Actually, it took more time to explain than it really did to do the inspection. At any rate we decided that a compression test was in order so we could verify the internal engine status. That way we wouldn't buy any tune up parts until we were sure that the engine was in reasonable mechanical condition. Our tests showed a fictional compression reading of 85, 80, 82 and 86 psi. That is well within a
... [Read Article]
Latest Ad:
1958 FORD RARE 4x4 801 TRACTOR, ELENCO/FRONT DRIVE, FRONTLOADER AND WEIGHTED REAR WHEELS, FIVE SPEED, LIVE PTO, GAS ENGINE, NEW REAR WHEELS AND TIRES, ENGINE RUNS.
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|