Posted by Case Nutty 1660 on July 16, 2018 at 12:33:29 from (162.252.129.7):
In Reply to: Re: cost to make hay posted by SVcummins on July 16, 2018 at 10:53:28:
Sorry guess I am gun shy, as I get jumped on here more often than not,, yes I was aware the 4020 held a bit less fuel it was all but empty with the gauge well to the bottom of the red in less than 6 hrs run time,, 1030 used 3/4 of a tank at best in 12 hrs, now at the tie we were custom plowing so we roaded a lot of places and that 4020 would flat out Scoot down the road compared to the 1030 lol been a lot of years since then but I still remember running the 4020 with all the doors and windows open when it was cold in the spring due to what I called the seat heater they had in them,, I am sure you may not notice as fast as me but I never had a tractor with a seat heater before lol that winter we mounted a new Waldon dozer on it to plow snow with,, it was warm and toasty even when it was well below zero, the powershift was handy on the dozer but those dash hyd controls was a pain for a short guy like me to reach lol wish I had both of those 4020's we traded for that year and they were is the same shape as then,, they would bring a nice price,, the one was a year old with syncro trans it had less than 300 hours on it the ps one was two or three seasons old at the time they were slow movers,, as we had them on lot for over a year before we sold them both to one buyer,, Dad had made the newspaper ad wrong and it said one or both for 5000,,, was supposed to say choice for 5000 lol ahh live and learn
Upload one or more videos to your post. Photo filesizes should be less than 300K and Videos, less than 2MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Tractor Profile: Allis-Chalmers Model G - by Staff. The first Allis-Chalmers Model G was produced in 1948 in Gasden, Alabama, and was designed for vegetable gardeners, small farms and landscape businesses. It is a small compact tractor that came with a complete line of implements especially tailored for its unique design. It featured a rear-mounted Continental N62 four-cylinder engine with a 2-3/8 x 3-1/2 inch bore and stroke. The rear-mounted engine provided traction for the rear wheels while at the same time gave the tractor operator a gre
... [Read Article]
Latest Ad:
Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
