Lots of good opinions. For the composite decking material, remember like anything, there are some kinds that are much better than others .... and price differences are usually a good indicator of which composite decking is best. Remember thought that even with composite decking, you are still at the mercy of wood rot underneath for your beams or joists.
I have a friend who complains that his dark-colored south-facing composite deck gets very hot in direct sunlight and his young kids have to be careful when wandering onto it barefoot.
Anyways, I prefer 2x6 wood decking myself, and despite what people say about which way to face the boards up or down depending on the annual ring orientation, that is a bunch of hogwash. Some boards will cup up regardless of which way the rings are orientated, I've been there, done that and seen that.
If a person is using 2x6 wood though (preserved is best), I would recommend cutting a lengthwise "kerf" or sawcut down the middle of the board on the bottom side of each 2x6 before nailing or screwing down to your joists. The kerf slot should be about half the thickness of the board, so about 3/4" deep on a 1 1/2" thick 2x6. You can brush a bit of preservative into that slot before installing the boards. When installing, the second nail or screw will fasten the board down FLAT and will tend to prevent (hopefully) the cupping that so often occurs. Lots of videos on the web, just Google something like " saw kerf cuts in deck lumber" .... etc.
One other thing, for those concerned with the 5/4 deck boards sagging a bit, for sure 16" centers on the joists (stringers) would be good, and even 12" is best (although maybe a bit of overkill). But really, a few more joists in a project won't make much difference in overall cost.
Upload one or more videos to your post. Photo filesizes should be less than 300K and Videos, less than 2MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Memories of an IH Super A When I was ? up to 10, I worked on my Papaw's farm in Greeneville, TN every summer. As I grew older (7), it was the thrill of my day to ride or drive on the tractor. My Papaw had a 1954 IH Super A that he bought to replace a Cub. My Papaw raised "baccer" (tobacco) and corn with the Super A, but the fondest memory was of the sawmill. He owned a small sawmill for sawing "baccer" sticks. The Super A was the powerplant. When I was old enough (7 or 8), I would get up early and be dressed to
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
