Posted by Bruce from Can. on August 08, 2017 at 08:30:55 from (76.69.28.6):
In Reply to: Silage bunker??? posted by cumminspuller on August 08, 2017 at 08:04:56:
I expect you will receive many replies to this post. And I don't think there really is one answer . Much depends on how much tolerance you have to spoilage. Some will just flip out and tell you that you are wasting too much with and spoilage. Tower silo fans get some spoiled silage to from stave silos, but as the unloaders chew it up and spit the silage down the shoot , it all gets mixed in , and you can't see it. Now more the the point of your question, I have put up silage in a cement floor - earth side pit silo , that is cut into the side of a hill , for the last 14 years. I don't put plastic down on the floor , or up the sides. I do cover with plastic. Just don't believe the silage loss would worth the frustration of trying to fill and pack the corn , without destroying the plastic in the process. We get some spoilage , but very little. Cutting the corn at the right moisture, and doing a good job packing is more important. I the situation you describe , with a flat pad of concrete, and no sides , not so sure that I would bother with the bales rowed up to make sides. The reason is , you will not be able to pack tight against the bales without the bales moving. And if you use round bales the round sides will add to the packing problem. I would just forget sides , and then you can drive your packing tractor right up the side, as well as end to end. I would also not worry much about going wider than the cement pad when doing this type of pile , as the total volume of silage not on the pad is minimal compared to the extra depth of silage that you can get packed on the pad. Only thing I will say to watch for is , be sure water will not run on to or in to your silage pile . Best of luck, Bruce
Upload one or more videos to your post. Photo filesizes should be less than 300K and Videos, less than 2MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Converting from 6 Volt to 12 Volt - by Chris Pratt. It's a common problem for old machines especially when the weather starts to dip below 40 and the tractor isn't fired up as often. You are probably used to the 12 volt Diehard, charged with 200 amp alternator of your 3/4 ton that always is ready and always starts. It's this type of experience that brings about the many queries we get for 12-volt conversion kits. Since only a few kits are available (we sell kits for the
... [Read Article]
Latest Ad:
Late 50s early 60s international harvester 560 with cultivator
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
