Posted by NCWayne on May 26, 2017 at 22:09:58 from (71.30.77.14):
One of my customers just bought part of an estate that belonged to an old well driller. In the deal he got a IH 135B 4 cylinder, gas, power unit. It has a Twin-Disc clutch on the back. I imagine the engine would have to be rebuilt as it's been sitting outside for years, but it does appear to be complete.
The other engine is a BIG 6 cyinder that starts on gas or kerosene (not sure which) and then shifts to diesel. The block is stamped UD 1091 M 58(0 ?). It's still sitting on the back of an old B36P Mack truck, and is actually the drive for a HUGE Worthington air compressor. Again, it's been sitting for years, and in it's case I imagine it's probably locked up. Even so, it's all complete.
I know there are guys out there that both collect, and in the case of the smaller power unit, use these old engines, so I told the guy I'd post on here and see of there might be any interest, or if anyone might know someone who would have in interest.
He's also got an old, 21 inch Monarch lathe. It's flat belt drive but it has the overhead, electric, two speed, gearbox driven by a 3HP single phase motor. There is also a small Kerney and Trecker boring mill.
Finally, there is what looks like a Deere 40 (that's based on the fact the engine looks a lot like the one in my old 440IC dozer). It was split in half for something, and it appears the flywheel housing is missing. Otherwise, it looks like both the front end/engine, and the rear end are both is complete otherwise. The tractor also had spin out rims, but I believe they are rusted out. Even so it also has the cast weights on the rear.
My email is open if anyone wants to get up with me about this stuff.
Again, any interest in any of this stuff, please let me know. The guy is trying to move this stuff as fast as he can, and if it's possible to sell some of it in place, and not have to move it, he'll be way ahead in making at least a little money on this deal.......and saving some nice old stuff from the scrapper.
Upload one or more videos to your post. Photo filesizes should be less than 300K and Videos, less than 2MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - The Ferguson System Principal An implement cutting through the soil at a certain depth say eight inches requires a certain force or draft to pull it. Obviously that draft will increase if the implement runs deeper than eight inches, and decrease if it runs shallower. Why not use that draft fact to control the depth of work automatically? The draft forces are
... [Read Article]
Latest Ad:
1965 International Harvester McCormick Farmall cub tractor 2,500. Two owner tractor. My grandfather bought new in 1966, then we inherited it. Have all the paperwork original manual and all maintenance records. It starts and moves. Comes with underbelly mower, plough, and some other attachments.
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
