Posted by alskdjfhg on December 09, 2016 at 06:13:36 from (129.7.0.149):
Instead of finding the older thread, I'll just make a new one.
Got the final price on the building, the dirt work I'm doing with another guy, here is my unofficial final price;
40X80X16 building 6" slab (2 beams running the length of the building 12"x20"x80' which will be spaced apart 20' centered in the building, with 5- 12"x20" beams running perpendicularly between the 80' center beams, along with 12x24 perimeter beam) This will provide plenty of support for your equipment in the "drive through" area.
We will have 6x6 posts set to 72" deep in the running wall posts and 8x8 posts set to 96" deep on the corners and door frame posts with the door posts going to the top of the truss.
Walls and roof to have radiant barrier.
3/12 pitch roof woth manufactured trusses with gerts on 24" centers on walls and roof, (all gerts to be joist hangered in place)
Total for all $ 64,225.00
Additional items
16x80 lean to 6x6 posts on 16' centers with 3x12 beam on 2/12 pitch. Framed with all treated lumber
$5,400.00 per lean too
I am waiting on confirmation on the use of the aluminum wire for a quote on the underground and meter/breaker panel.
If we can use the aluminum the price will be $2,650.00 for a 400 amp underground wire 400 amp meter can ( this allows you to add another 200 amp panel later.) and a 200 amp breaker panel.
So what do ya'll think? How bad are these prices? More than I wanted to spend, that's for sure.
Upload one or more videos to your post. Photo filesizes should be less than 300K and Videos, less than 2MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - The Fordson F Ignition System - by Anthony West. A fellow restorer contacted me earlier this year asking for some help and advice on a model F that he was restoring. He had over a period of months spent a fair amount of his hard earned cash on replacement parts for the old "trembler" ignition. Sadly though all his efforts seemed to be a waste of time and money as he still couldn''t get the temperamental old thing to run correctly!! If i said that this was a little frustrating for him that would be "conservative" in fact the problem had reduce
... [Read Article]
Latest Ad:
For sale Farmall super A tractor is complete and has just been setting for awhile,it was running when pulled out of the barn,shouldn’t take to much to get it going asking 1100.00
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
