Posted by Texasmark1 on August 12, 2016 at 06:50:14 from (184.20.237.101):
Gotta eat crow on this one. I like stamped decks on mowers because of the improved grass exit flow and reduced tendency to clog and having to be cleaned due to wet grass buildup is highly reduced. Never had a problem and was noticing that ZTs for sale at the local outlets are now offering more with stamped decks.....yes to reduce price and get them "sellable".
Have this neighbor that dings me every time he breaks something. About a week ago he brings his Husqvarna 20k46 over for me to weld up some cracks in his deck. I welded them up and away he went. Yesterday he comes back over and he has 4 new cracks, with one being complete severance of 2 sides of the right rear bracket that mounts the deck to the tractor's support rod. Besides that the deck looked like what you often see on shredder decks.....dimples where rocks and such have hit the under side with great force.
I have the same mower with about 600 hours with the deck in like new condition, minus some rubbed off paint obviously. Not believing what I was seeing, I eased over to the hour meter, turned the key on and the unbelievable number of 96 hours popped up on the display.
So, I'll eat crow. Welded decks do last longer than stamped under certain circumstances.
This became a dealer only replacement as the "Product number" had a -06 at the end meaning that there were 6 versions of this deck used. So he ordered a new deck, $300 + $100 shipping. He has a 6' brush hog and 4600 Ford (that I welded the trailing wheel bracket back together for him about a month ago) that he could be using when he needed to clip his pasture. Maybe this financial outlay will help him to use the right tool for the job.
Upload one or more videos to your post. Photo filesizes should be less than 300K and Videos, less than 2MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - My Ford Golden Jubilee - by Troy Estes. This article is about my '53 Ford Jubilee and a story that starts with taking the tractor to my brother's Starter/Alternator Rebuilding shop for a wiring fix. The generator was shot as well as all the wiring. I dropped off the tractor expecting a transformation from a 6 volt to a 12 volt system utilizing the original generator housing, and a total rewiring of the whole tractor. The front end center pin bushing was worn also so I ask that they replace it if they had time. Well, that’s wha
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
