Posted by John M on June 14, 2016 at 05:49:59 from (104.129.204.55):
Im not electrician, so bare with me. Here at work, we have one warehouse that has to maintain 60 degrees year round. To do this we have a total of 4 chiller units. 2 are more or less back up, and had seldom came on except on very hot days. They are older units that work, but cant keep up with 60 degrees. 2 bigger units were installed in the 70s, and one has just been replaced with a new outside unit and air handler. The other has had the outside unit replaced both within the last 2 years. Now, the older units are on a seperate transformer outside from the new units. No issues there, but the new units heat up the main breaker inside to the point it trips. Old units have line from the transformer, to meter base, to inside breaker, and from there to each unit, where it has its own breaker for both inside and outside units. The new ones, well, heres the point ofthe post. The guy who installed the new units came by to check the untis, and determined the source of the heat in the breaker was from the fact the new units pulled more amps, and possibly the age of the breaker as well, is whats causing it to trip. So he was going to install a new breaker inside. He pulled the meter outside, checked for power and there was still power to the breaker. Heres what he found: The lines from the transformer go to the building, there is some type of setup attached to the outside wall of the building that has 3 "blocks" for a lack of a better word, that has a hole in the center of each block. The wire wraps around the blocks going through the hole in each, then comes to the inside breaker. From the bottom of the breaker, 3 wires go to meter base, and from there to the chiller units, where each has its own breaker for each unit. Boss said the original units were installed in the 70s, and as far as he knew, no other work has been done or needed. So finally my question: Why would the "hot" wires from the transformer been connected directly to the breaker?
(If I could post pics from work I would. I may try this evening from home.)
Upload one or more videos to your post. Photo filesizes should be less than 300K and Videos, less than 2MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - The Nuts and Bolts of Fasteners - Part 2 - by Curtis Von Fange. In our previous article we discussed capscrews, bolts, and nuts along with their relative hardness and thread sizes. In this segment we will finish up on our fasteners and then work with ways to keep them from loosening up in the field. Capscrews, bolts and nuts are not the only means of holding two parts together. When dealing with thinner metals like sheet tin, a long bolt and
... [Read Article]
Latest Ad:
Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.