Posted by RandyB(MI) on March 10, 2016 at 08:43:53 from (75.133.131.65):
In Reply to: Todays steel posted by Eldon (WA) on March 09, 2016 at 21:27:24:
Like "RM-MN" said down a few posts, "BEAN COUNTERS" says it all. Steel can and is still as good or better in some cases as it ever was. Customers have more choices as to the price / quality than they ever had and just like carpeting, some trying to save a buck and make their job look "needed" will always take the $ 10 a yard carpeting. In the case of steel it will be the welders/benders/fabricators and end user that finally pay the price. I worked in a factory producing huge whole tree grinders/chippers and I've seen this first hand. 1/2" steel plate we used to bend 90 degrees without problems, now cracks at the bend and sometimes twice and their answer is to call out welders and go around machine and weld up all the cracks.Mill scale is another big problem. So bad it looks like "alligator hide" and my paint dept would get called out on it as if it were a "paint" problem. Once I proved it to them what it was and that they were having rust problems 6 mos down the road with customers, they priced "good" steel against the scab steel and would have had their problem solved be it not for the "bean counters". Take one guess which steel we continued top use? At least they knew better than to come to me as their "goat". The "beaners" will continue to win this war until a competitor comes forward and identifies it to customers and goes the other route. Not too likely. I couldn't even get them to go to urethane paint/primers until 2008 and then only because our customers/dealers were royally 9issed and forced it. Even then they forced our supplier to cut his bid/quality to come in where the "beaners" felt comfortable. Welcome to big business!
Upload one or more videos to your post. Photo filesizes should be less than 300K and Videos, less than 2MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Field Modifications (Sins of the Farmer) - by Staff. Picture a new Chevrolet driving down the street without it's grill, right fender and trunk lid. Imagine a crude hole made in the hood to accommodate a new taller air cleaner, the fender wells cut away to make way for larger tires, and half of a sliding glass door used to replace the windshield. Top that off with an old set of '36 Ford headlight shells bolted to the hood. Pretty unlikely for a car... but for a tractor, this is pretty normal. It seems that more often than not they a
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
