Thanks everyone. I forgot to mention that i had already used the scarifiers to break up the topsoil, and go as deep as i could get them with my limited experience. Great idea on adding weight, i might try it.
So far, i ended up making a homemade trencher based off of this video:
https://www.youtube.com/watch?v=nh_mYjWfJeY
I didn't make the notches, cause i think he said somewhere that they aren't really necessary... but dont quote me on that.
I went to home depot and got the thickest piece of angle iron they had... 4 feet long, 2" wide and 3/16" thick for $22. It works really good, and would be almost all you need if you were only laying a small pipe... but since i'm going to bury 4" pvc, i have to go back and forth over it a few times to widen it out. I suppose i could use 2 next to each other to make wider passes... but then it's $45 and at that point, i would probably better off trying to find something like this for for a little more:
Right now there is one of those on ebay for $60 with free shipping. If i hadn't already bought the angle iron, i might have went ahead and got it. It looks like i could just slide it in where my rippers go, and drag it like that.
Anyway, here is the homemade trencher on the tractor:
Wider sides would scoop more dirt out, and thicker would be better as well... but again, it works really really well for what it's doing. You can see a bend in the iron... that was unintentional because at one point i tried going in reverse through the trench... i guess it was weaker in that direction, and it bent... but it actually turned out ok, because now when i drive forward i think it helps it dig down and scoop into the trench.
It breaks it up really good, then i scoop out the dirt with a shovel (of course there is still a bit of digging)... also roots are a pain, but i have a reciprocating saw with an old blade on it that i run down the side of the trench when i encounter one, and cut it out.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - My Ford Golden Jubilee - by Troy Estes. This article is about my '53 Ford Jubilee and a story that starts with taking the tractor to my brother's Starter/Alternator Rebuilding shop for a wiring fix. The generator was shot as well as all the wiring. I dropped off the tractor expecting a transformation from a 6 volt to a 12 volt system utilizing the original generator housing, and a total rewiring of the whole tractor. The front end center pin bushing was worn also so I ask that they replace it if they had time. Well, that’s wha
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
