Posted by andy r on January 04, 2016 at 18:05:48 from (166.181.83.95):
In Reply to: Auger Design posted by 2510paul on January 04, 2016 at 15:06:52:
I rebuilt the hopper and incline on a 60 some foot grain auger this last fall. The main long auger was an 8 inch auger. The incline and the hopper was more like a 7". According a replacement auger supplier as the auger gets larger in diameter the clearances get larger. I believe on the 8 inch tube it was around 1/2 to 3/4 each side. I was surprised. Certainly those dents do not help as well as the bow. Too much drag. Wet corn and the incline all increase the power needed. 20% moisture isn't that high. Also remember you might be raising more bushels per acre compared to when that picker was new. A 6" auger should carry quite a bit of corn. You could replace the tubing. I buy 10 and 20 foot chunks of 6" tubing with 1/8" walls from an area metal supplier. They stock it. I can't remember if it is around $4.00 a foot. Might be that the auger is OK. The last auger flighting I bought was from Nebraska I think - shipped UPS. Goggle auger flighting and you will find them. They send it via UPS in 5 foot pieces interwoven into each other. Cut the old off and install the new or maybe just the one end needs to be repaired. Again I think I paid about $4.00 a foot. I have even cut the dented section out of a auger tube and reattached with a collar. I would check to see that the drive components are not slipping. If slipping is going on the auger will fill up and the power requirement will increase to the point that it can't turn it. Good luck.
Upload one or more videos to your post. Photo filesizes should be less than 300K and Videos, less than 2MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - My Ford Golden Jubilee - by Troy Estes. This article is about my '53 Ford Jubilee and a story that starts with taking the tractor to my brother's Starter/Alternator Rebuilding shop for a wiring fix. The generator was shot as well as all the wiring. I dropped off the tractor expecting a transformation from a 6 volt to a 12 volt system utilizing the original generator housing, and a total rewiring of the whole tractor. The front end center pin bushing was worn also so I ask that they replace it if they had time. Well, that’s wha
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
