Posted by jtedescucci on September 11, 2015 at 06:56:30 from (75.143.155.126):
In Reply to: Re: 6605 3-point lift posted by Tx Jim on September 10, 2015 at 09:18:33:
Jim - I'm in the same boat with you. Have talked with at least one guy who used to work for Deere, and his OPINION is that one of the reasons they went to electronic controls was that they wanted to cut back on the work being done on Deeres by third parties - in other words, by shops that are NOT franchises & are not paying Deere any royalties or fees. I am NOT trying to "bad mouth" Deere here. Their approach MAY be sound business practice - and I even own & operate a Deere myself(5410) - but I DO think that this tactic is likely to leave a bad taste in the mouth of anyone who happens to come up "on the short end of the stick". My buddy - who I am TRYING to help - has very limited funds (don't we all) - and really cannot afford to pay Deere(or anyone else) $1200 for a hydraulic control unit (HCU ... and I thank you ALL for the diagrams & sketches). I had a 1984 Chrysler sedan that was largely controlled by computers & brains, and when something went wrong the problem-solving quickly became a "crap shoot" in which I guessed by replacing the parts that seemed most likely to have failed. I remember very well that the MAIN "brain" cost less than $300 ... and so it bothers me some that the HCU on this tractor costs roughly FOUR TIMES as much (I believe the parts are comparable) . . . . I knew when I posted my last question that the question MIGHT offend someone ... and I wanted more than anything else NOT to do that ... but since my knowledge & experience on this subject are SO LIMITED I felt the need to explore just a little further. I figure that the most inexperienced beginner on this forum MUST know more than I know about these matters, and so I am left with the task of asking questions & trying to get to the root of the problem. Again, I thank ALL who have been so kind as to reply & share their knowledge & experiences. Four or five guys here have REALLY "stepped up to the plate", and Dean(my buddy) & I appreciate that SO MUCH. I don't know if it's allowed by the forum rules, but I want you to have this: "[email protected]" .... If, in the future, you can think of ANYTHING ELSE - please DO contact me. You (& others) have been very helpful & kind - and I thank you. "May God Bless" ....... FredT
Upload one or more videos to your post. Photo filesizes should be less than 300K and Videos, less than 2MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Tuning Up Your Tractor: The Battery - by Curtis Von Fange. Buried somewhere beneath the sheetmetal, under the gas tank, or stuffed in front of the radiator is the battery. This elusive and neglected component of the tractor is the hardest to get to when it is dead and in need of a jump. But usually, the storage battery is a storehouse of electrical energy waiting to be released a the flick of a switch. A few maintenance tips and periodic cleaning will keep it charged for the duration of its life span. The battery is made up of a number of lead bas
... [Read Article]
Latest Ad:
For sale Farmall super A tractor is complete and has just been setting for awhile,it was running when pulled out of the barn,shouldn’t take to much to get it going asking 1100.00
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
