Posted by John T on August 18, 2015 at 18:47:21 from (216.249.74.3):
In Reply to: New home electrical posted by SKYBOW on August 18, 2015 at 07:26:56:
As always, Legal or Electrical questions draw the most opinions of any other topics lol. Everybody including yours truly crawls out of the woodwork with opinions about how to do things, including Billy Bob and Bubba who wired their shop while downing a case of beer and by golly it works fine HOW CAN YOU ARGUE WITH THAT ???????????
Regarding a few comments I saw below, in my many years as an Electrical Power Distribution Engineer, I NEVER PUT LIGHTS AND CONVENIENCE RECEPTACLES ON THE SAME BRANCH CIRCUIT. If I was working with a convenience outlet branch circuit, THE LAST THING I WANT IS FOR THE LIGHTS TO GO OUT OR THERE BE NO LIGHTS WHEN IM ON THE FLOOR IN THE DARK WORKING AN OUTLET. If an outlet load trips a breaker (MUCH more common then a light tripping it) I don't want the lights going out also.
Of course, Billy Bob and Bubba or even professional electricians are free to wire however they please (in accordance with or NOT in accordance with NEC), no argument from me. Its just NOT how I was taught or how I practiced, but yall do as you like.
My standard practice on convenience outlet branch circuits was to use 12 Gauge Wire, 20 amp rated receptacles, and of course protected with a 20 amp overcurrent protection device. On a lighting ONLY branch circuit where the max continuous load never exceeded say 11 or 12 amps, I "might" consider use of a 15 amp 14 gauge wire circuit.
Loose burned resistive connections, Neutral or Hot, too small wire, excess length of runs,,,,,,,,,,low input voltage,,, can all contribute to voltage drop and problems such as dim lights
Upload one or more videos to your post. Photo filesizes should be less than 300K and Videos, less than 2MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Uncle Cecil's Super A Lives Again - by Mike Purcell. A week or so out of most of my childhood summers was often spent with my Uncle Cecil and Aunt Sissie in the small East Texas town of Maydelle on their 80 acre farm. Some of my fondest memories of these visits are those of learning to drive a tractor at the helm of Uncle Cecil�s 1948 Farmall Super A. Uncle Cecil was the second owner of this wonderful little tractor, but it was almost as though he had adopted an infant. The original owner was a man from Minnesota who bought her from a local dea
... [Read Article]
Latest Ad:
For sale Farmall super A tractor is complete and has just been setting for awhile,it was running when pulled out of the barn,shouldn’t take to much to get it going asking 1100.00
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
